9. Contact Us
10 Customer Service
11. Trademarks
- For repair and maintenance of this product, contact your local dealer or our repair center.
- The attachment and USB cable are not covered by the warranty. If you need to purchase
any of these items, contact your local dealer or our information center.
- Spare parts for repairing and maintaining this product will be available for six years after
the product has stopped being manufactured.
f
Epson website http://www.epson.jp
Visit the Epson website for various product information, driver downloads, support
information, and more.
You can confidently expect excellent customer service from Epson.
FAQs are also published on the website.
We look forward to your visit.
http://www.epson.jp/faq/
* iPhone is a trademark of Apple Inc., registered in the U.S. and other countries.
* Bluetooth and the Bluetooth logo are trademarks of Bluetooth SiG, Inc. in the
United States. The ® mark is omitted in this manual.
8. Basic Specifications
Communication method
Bluetooth 2.1+EDR Class 2
Communication distance
Approx. 10 m (with no obstructions)*
1
Operation time
Approx. 4 hours*
2
Built-in battery
Lithium polymer rechargeable battery
Charging method
USB bus power (+5 V DC)
Charging time
Approx. 2 hours*
3
Operating temperature
range
0 to +40°C*
4
Storage temperature range
-20 to +45°C
External dimensions
50 (D) x 25 (W) x 15.5 (H) mm (excluding protrusions)
Weight
Approx. 15 g
*
1
The communication distance varies depending on the surrounding environment and the
performance of the Bluetooth device that is the communication target.
*
2
The operation time conditions are in compliance with our measurement conditions.
*
3
The charging time will increase or decrease in accordance with the usage conditions of
the charging battery.
Charging may take about 3 hours from the fully discharged state.
*
4
+10 to +35°C during charging of the battery (Charge the battery at room temperature as
much as possible).
6. Using this Product
1.
Hold down the control button on the unit for at least two seconds to turn
it on.
The blue status lamp flashes twice every two seconds.
2.
Turn on the Bluetooth setting on the smartphone.
3.
Tap
on the smartphone to start Epson M-Tracer for Golf.
The blue status lamp flashes twice every two seconds when the smartphone and
the unit are communicating.
4.
Tap the [Measure] button to switch to the measuring display.
5.
Tap the [Setup] button to set the club being used and the intended line of
flight.
6.
Tap the [Start] button to begin measuring.
The red status lamp turns on and the unit enters the measuring status.
7.
Square the club to the target line and remain still.
Remain still while the face of the club and the shaft are square with the target line.
When the unit detects that you are standing still (about two seconds), the blue
status lamp turns on and you can take your swing.
90°
Target Line
8.
Swing the club.
When the impact from the swing is detected, the blue status lamp flashes and the
data is transferred to the smartphone.
Repeat steps 7 and 8 to continue measuring your swings.
9.
Tap the [Stop] button to stop measuring..
10.
Tap the [<] button to switch to the analysis display.
11.
Hold down the control button for at least two seconds to turn off the unit.
The unit is also turned off automatically after approximately 10 minutes if the
smartphone is on any other display than the measuring display.
-
Note that the procedure for swing measurement and the lamp indicators may
be updated when Epson M-Tracer for Golf is updated.
For the latest specifications, see the Help of Epson M-Tracer for Golf.
-
If the unit enters a normal error status (the red status lamp flashes on and off
every one second), follow the displayed instructions.
-
If the unit enters a hardware error status (the red status lamp turns on for five
seconds and then turns off for 0.5 seconds repeatedly), turn the unit off and
then back on.
-
If the unit operation becomes unstable, insert the reset hole with a toothpick,
and reset the unit.
7. Viewing the Help
Your swings are measured using Epson M-Tracer for Golf. For details on using the product,
see the Help.
1.
Tap the menu button at the top left of the analysis screen.
2.
Tap the Help button.
For further details on using this product, visit the Epson product information page (
http://
www.epson.jp/products/msensor
).
5. Mounting the Unit to a Golf Club
1.
Attach the attachment to the grip.
Attach the attachment so that the golf club mark on the side of the attachment
match the orientation of the golf club. The attachment may come off if it is
attached upside down and it may cause an injury.
Make sure the center of the attachment is aligned with the center of the golf club.
The M size has
2 marks.
Golf club mark
2.
Mount the unit to the attachment
Slide the unit onto the attachment rails.
If it is difficult to slide the unit,
try sliding it
while pressing the parts indicated by the
marks
on the sides of the attachment.
You can also
try changing the attachment
mounting position to a location where
the grip is narrower
.
Slide the unit along the rails until it comes into
contact with the stoppers at the ends.
3.
Check the mounting status.
After mounting the unit, confirm that the attachment and unit are secured
properly.
If the attachment is mounted loose (if it turns), change the attachment mounting
position to a location where the grip is thicker.
-
We recommend mounting the unit to the lower end of the golf club so that
it cannot be seen in the address position. If you find it difficult to check the
status lamp, try mounting it at the upper end of the golf club.
-
Normally use the M size attachment. If you use a club with a narrow grip such
as a club for ladies or a club for juniors, use the S size attachment. If you use a
club with a grip that is too thick to mount the M size attachment, use the L size
attachment.
-
Attachment mounting marks may be left on the bottom of the unit but this will
not cause a problem with the functions of the product.
Stopper
Install Epson M-Tracer for Golf on the smartphone.
1.
Download Epson M-Tracer for Golf to the smartphone.
Search for and download Epson M-Tracer for Golf.
2.
Install Epson M-Tracer for Golf on the smartphone.
Follow the on-screen instructions.
3.
Tap
.
Epson M-Tracer for Golf starts.
4.
You need to register the first time you use Epson M-Tracer for Golf.
Follow the on-screen instructions to perform Epson Sensing ID and player
registration.
• The Epson Sensing ID allows you to use multiple services and functions provided by
Epson with one ID and password. More services will be added over time.
• Epson Sensing ID and MyEPSON ID are different.
The user is responsible for any communication charges incurred when
exchanging data using your smartphone. For information on charges and other
items, contact your carrier.
4. Preparing the Application
f
Information Center
Call us if you have any questions about the product.
Support from the Information Center is only available in Japanese.
[Tel] 050-3155-8280
- Call 042-585-8590 if you cannot use the above phone number.
f
Repairs
Take the product to your reseller or send it to the following repair center.
Matsumoto Repair Center
[Address] Epson Service Corporation, 1563 Kanbayashi, Matsumoto-shi, 390-1243
[Tel] 050-3155-7110
* Note that the address and telephone number are subject to change without
notice.
* See the Epson website for details on repairs. http://www.epson.jp/support/
- Call the following phone number if you cannot use the above phone number.
Matsumoto Repair Center: 0263-86-7660
f
Showroom
* You can also visit the Epson website for more details.
http://www.epson.jp/showroom/
Epson Square Shinjuku, 1F Nishi-shinjuku Mitsui Bldg, 6-24-1 Nishi-shinjuku,
Shinjuku-ku, Tokyo 160-8324
[Opening hours] Monday to Friday 10:00 - 17:00 (excluding bank holidays and our
designated holidays)
f
Purchasing Optional Products and Consumables
You can purchase them from your nearest Epson reseller or Epson Direct
(http://www.epson.jp/shop/ or call free to 0120-545-101) (May 2012 current)