Wuxi Weida Intelligent Electronics Co., Ltd.
无锡威达智能电子股份有限公司
5
/
9
3
、
遥控器操作说明
Remote control instructions
1.
遥控器基本要求
Basic requirements for remote control
1).
当连上蓝牙，遥控器发送蓝牙键值；未连接上蓝牙，则发送红外键值。
1). When Bluetooth is connected, the remote control sends the Bluetooth key value; when Bluetooth
is not connected, the infrared key value is sent.
2).
指示灯：红外：红色，每按一次按键，指示灯闪一下。
2). Indicator light: infrared: red, each time you press the button, the indicator light flashes once.
3).
低电压提醒：电量低于
2.4V
时，指示灯快速闪烁，只要还在操作，就一直保持闪耀状态，当不再
对遥控器进行操作后，闪烁
5
次或闪烁
3
秒后，停止并熄灭。
3). Low voltage reminder: When the battery is lower than 2.4V, the indicator light flashes quickly, as
long as it is still in operation, it will keep flashing. When the remote control is no longer operated, it
flashes 5 times or flashes for 3 seconds and then stops And goes out.
4).
配对方法：
a.
同时按遥控器上的“
ENTER
”
+
“
HOME
”三秒
,
发送对码信息；
b.
没配对成功时，如果还在按“
ENTER
”
+
“
HOME
”键就要一直发配对广播，以便用户可以
配对。
c.
按一次“
ENTER
”
+
“
HUME
”键就要能配对成功，不要反复清除配对再配对。一次按键配对
成功后可以不再发配对广播，直到下次重新按键。
Connection interval
＜
12ms
4). Pairing method:
a. Simultaneously press
“
ENTER
”
+
“
HUME
”
on the remote control for three seconds to
send the code matching message;
b. If the pairing is not successful, if you still press the
“
ENTER
”
+
“
HUME
”
keys, you must
keep sending the pairing broadcast so that the user can pair.
c. Press
“
ENTER
”
+
“
HUME
”
key once to successfully pair. Don't clear the pairing and pair
again. After a key pairing is successful, the pairing broadcast can no longer be sent until the next
time the key is pressed again.
Connection interval
＜
12ms
5).
按键超时：如果连续按下一个或多个按键超过
30
秒，则遥控器停止传输以保护电池放电。
5). Key timeout: If one or more keys are continuously pressed for more than 30 seconds, the remote
control will stop transmission to protect the battery from discharging.
6).
遥控距离：≥
10m
6). Remote control distance:
≥
10m
7).
蓝牙设备名称：
EPSON PJ REMOTE
7). Bluetooth device name: EPSON PJ REMOTE
8).Bug Report:
按下【
D-PAD CENTER
】
+
【
BACK
】键
1
秒钟以上，以获得
STB
错误报告；在
IR
模
式下，发送的代码数据为
0X96
。
8).Bug Report: Press
【
D-PAD CENTER
】
+
【
BACK
】
key for more than 1 second to get STB error
report; in IR mode, the code data sent is 0X96.
