manualshive.com logo in svg

Epson FX-1180 - Impact Printer, Руководство пользователя

Поделиться
Скачать
Epson FX-1180 - Impact Printer Скачать руководство пользователя страница 175

If you are not sure whether you need an optional interface or would like
to know more about interfaces, contact your dealer.

Follow the steps below to install an optional interface card.

1.

Make sure the printer is turned off. Unplug the printer’s power cord and
disconnect the interface cable.

2.

Remove the screws securing the shield plate to the back of the printer
and remove the plate.

3.

Slide the interface card along the slots on both sides of the interface
compartment. Firmly push in the card to make sure the connector at
the back of the card is fully inserted into the printer’s internal socket.
Then replace the screws and tighten them.

Note:
Store the shield plate in a safe place; you will need to reattach it if you remove the
interface card later.

To remove the interface card, reverse the steps above.

g6-3-1

g6-3-2

L

Gentian-W  Rev.C

A5 size

Appendix A

11/14/97

pass 0

A-26      

Enhancing Your Printer With Options

Содержание FX-1180 - Impact Printer




































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды