Epson EB-1751 Скачать руководство пользователя страница 100

Status

Cause

Remedy or Status

If the lamp is not cracked

: Reinstall the lamp and turn on the power.

If the error continues

: Replace the lamp with a new one and then turn on the power.

If the error continues

: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest

address provided in the Epson Projector Contact List.

s

 

Epson Projector Contact List

If the lamp is cracked

: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be

projected until the lamp is replaced.)

s

 

Epson Projector Contact List

When using at an altitude of 1500 m or more, set 

High Altitude Mode

 to 

Mode1

 or 

Mode2

.

s

 "Extended Menu" 

p.84

Auto Iris Error
Power Err. (Ballast)

Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.

s

 

Epson Projector Contact List

High Temp Warning

(This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)

Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.

If the air filter is clogged, clean or replace it.

s

 "Cleaning  the  Air  Filter"  

p.112

,   "Replacing   the   Air   Filter"  

p.117

Replace Lamp

Replace it with a new lamp.

s

 "Replacing the Lamp" 

p.114

If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a
new lamp as soon as possible.

a

See   the   following   if   the   projector   is   not   operating   properly,  even  though  the  indicators  are  all  showing  normal.

s

 "When  the  Indicators  Provide  No  Help"  

p.101

If  the  indicators  are  in  a  state  not  shown  in  this  table,  stop  using  the  projector,  remove  the  power  plug  from  the  electrical  outlet,  and  contact  your  local  dealer  or
the  nearest  address  provided  in  the  Epson  Projector  Contact  List.

s

 

Epson  Projector  Contact  List

Problem Solving

100

Содержание EB-1751



















































































































































Отзывы: