manualshive.com logo in svg

Epson C31C514452, Техническое справочное руководство

Поделиться
Скачать
Epson C31C514452 Скачать руководство пользователя страница 70

3-28

   Setup

Rev. H

3.4.7.1  Serial Interface model

Before connecting any of the cables, make sure that both the printer and the host PC are turned 
off.

1. Plug the cable connector securely into the printer’s interface connector.

2. If the cable connector has screws on it, tighten the screws on both sides of the connector.

3. If your interface connector has a grounding wire, attach it to the printer using the screw 

labeled FG, which is next to the interface connector.

4. Attach the other end of the cable to the host PC.

Note:

When using serial interface, you need to adjust serial communication using the DIP switches. See 
“Adjusting the DIP Switches” (page 3-15) for details.

When using serial interface, see “

Serial Connection

” in Chapter 2 also.

3.4.7.2  Parallel Interface Models

1. Press the connector on the end of the interface cable firmly into the interface connector on 

the connector panel.

2. Press down the clips on either side of the connector to lock it in place.

3. For interface cables equipped with a ground line, attach the ground line to the screw hole 

marked "FG" on the printer.  

4. Connect the other end of the interface cable to the host computer.  

3.4.7.3  USB Interface Models 

1. Attach the locking wire saddle at the location shown in the figure below.  

2. Hook the USB cable through the locking wire saddle, as shown in the figure below.  

Содержание C31C514452



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды