Epson C11C638001 - LQ 300+II B/W Dot-matrix Printer Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 120

background image

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio or
television reception. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

❏

Reorient or relocate the receiving antenna

❏

Increase the separation between the equipment and receiver

❏

Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected

❏

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will
invalidate the FCC Certification of this device and may cause interference levels which
exceed the limits established by the FCC for this equipment. It is the responsibility of
the user to obtain and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables connected to unused
interfaces.

Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.

For Canadian Users

This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the radio interference regulations of the Canadian
Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de Classe B prescrites dans le règlement sur le
brouillage radioélectrique édicté par le Ministère des Communications du Canada.

L

Blackberry REV.E

A5 size

Front

96/04/17

ii

«
...
2
3
4
5
6
...
»

Содержание C11C638001 - LQ 300+II B/W Dot-matrix Printer

























































































































Отзывы:

Нет отзывов

Похожие инструкции для C11C638001 - LQ 300+II B/W Dot-matrix Printer

Pixma G1000 series

Бренд: Canon Страницы: 2

Pixma G1000 series

Бренд: Canon Страницы: 80

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 44

Бренд: Datamax Страницы: 2

Бренд: Canon Страницы: 521

Бренд: Canon Страницы: 456

Бренд: Konica Minolta Страницы: 266

CR10 XZ (Belt Z)

Бренд: ExoSlide Страницы: 12

Бренд: Olivetti Страницы: 139

Beta Prusa Standard

Бренд: 2PrintBeta Страницы: 67

Бренд: Xerox Страницы: 20

Бренд: Ricoh Страницы: 2

IM C6000 Series

Бренд: Ricoh Страницы: 2

Markoprint X4JET

Бренд: Weber Страницы: 177

Бренд: Lexmark Страницы: 2

Бренд: Copystar Страницы: 1

Бренд: BT Страницы: 64

Бренд: Citizen Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды