background image

7

Do not install this product where it may be subject to impact or vibration.

Do not install this product in direct sunlight or near a heater vent, fireplace, or other source of heat.

Do not install this product on a slanted ceiling.

Personal injury and/or damage to the equipment could result from dropping or mishandling this product.

Some of the components included with this product may be packaged in plastic bags. Keep plastic bags 
away from small children to avoid any risk of suffocation.

Do not place the components of this product near sources of heat or in direct sunlight.

Make sure nothing blocks the ventilation openings on any of the components. Allow for sufficient heat 
dispersion. Ensure that there is at least 8 inches (20 cm) between any ventilation openings and the walls or 
ceiling.

Where the mains plug is used as the disconnect device, the disconnect device shall remain readily operable.

When unplugging the power cord, handle it carefully. Hold the plug when unplugging the cord.

This product should be operated only from the type of power source indicated on the marking label. If you 
are not sure of the type of power supplied in your (school, business, home), consult your product dealer or 
local power company.

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk 
of fire or electric shock.

Keep the system components free from moisture, water, and dust.

Do not let insecticides, benzene, or thinner come in contact with any components of the system.

Never push objects of any kind through openings in the system components as they may touch dangerous 
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on 
the product.

Except as specifically explained in these instructions, do not attempt to service this product yourself. Refer 
all servicing to qualified service personnel.

Never disassemble or modify the product in any way. Dangerous electrical voltages inside the components 
can severely injure you.

When replacement parts are required, be sure the service technician has used replacement parts specified by 
the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result 
in fire, electric shock, or other hazards.

Do not place the system near high-voltage power lines or sources of magnetism. The system may not 
operate properly.

Содержание AP-60 - Projector Sound Solution





























Отзывы: