EPSON ActionDesk 4000+
System board components and connectors
Jumper settings
I Component
Processor
Jumper
Jumper
number
setting Function
J4
1-2
Enables game port
2-3*
Disables game port
J5
1-2*
Assigns PARALLEL port as LPT1
U27
Phoenix system and VGA BIOS; 15Ons. 8-bit operation
I
U28
System controller (UMC82C491); integrated system, memory,
and cache controller
U10
U4
Video controIler (GD5428); local bus VGA with integrated palette
DAC, dual-frequency synthesizer, BitBLT for GUI acceleration
Line and serial controller (UMC82C865F)
Keyboard/mouse controller (8042 compatible UPI)
I
U13
U35
Super I/O controller (UMC82C863); supports up to two diskette
drives, two serial ports, and one parallel pert
Local bus IDE controller (Adaptec AIC-24VL01Q)
J9, J10, J11
Disables diskette drive controller
Featured
J14
Off*
Disables IRQ9 for VGA
on
Enables IRQ9 for VGA
1-2
Selects a CPU clock speed of 33 MHz (486SX/33,
486DX33, 486DX2/66, and Pentium OverDrive
processor)
3-4
Selects a CPU clock speed of 50 MHz (DX/50)
5-6
Selects a CPU clock speed of 25 MHz (4865SX/25,
486DX2/50)
o f f ’
Selects fast speed
on
Selects 8 MHz speed
2-3*
Selects the system board battery
3-4
Discharges CMOS memory (this resets the SETUP
values to their factory defaults)
1-2.
Enables the IDE hard disk drive controller
2-3
Disables the IDE hard disk drive controller
1 - 2 . R e s e r v e d
U12
Clock generator (IMI SC 425 chip); 4V to 7V operating supply
range, 1
ns skew, CMOS or TTL compatible outputs
U20-23. U29-32
Cache SRAM sockets
J16***
I U36
I
U7, U8, U2, U3
Video DRAM; two
chips soldered at U7 and U8; two expansion
sockets at U2 and U3
CN2
Video connector: 15-
Spin. D-shell
CN3
CN5
CN4
Parallel port; 25-pin, D-shell
Serial port labeled COM1; 9-pin, D-shell
Serial
port labeled COM2: 9-pin. D-shell
J34
J35
I Mouse; 6-pin, mini-DIN
I
*Factory setting
** You can use MS-DOS to automatically reassign parallel and serial ports.
Check your MS-DOS manual for more information.
***Setting depends on CPU
External cache jumper settings*
J21
J3, J24
J30
J32
Speaker connector; 4-pin header
Reset; P-pin header
Hard disk drive; 4O-pin header
Hard d&k drive. weed. and power LED connector: 6-pin header
Cache size
J27
J28
1-2
1-2
Off
2-3
128KB
2-3
1-2
1-2
1-2
I S1
ISA 120-pin slat connector
I
U18. U19
SIMM sockets: 4MB standard on a SIMM in U19
2-3
l
If you have no external cache installed, the position of these jumpers does
not matter.
Jumper Settings
Processor type jumper settings
J36
J4-J11
J14. J16
I
J17
J19
486DX, DX2, or Pentium OverDrive
1-2,3-4
1-2
486SX
2-3
Off
J37
VGA jumper settings
VGA jumper function
Enable on-board VGA
Disable on-board VGA
J36
J37
on
on
Off
Off
J17
J19
J22
J25, J26,J27, J28
J34
EPSON ActionDesk 4000+ - 4
12/93