EPS PSB 10000 4U Скачать руководство пользователя

Страница: 28 / 110

30000800_manual_psb_10000_4u_30kw_en_04

1.9.9

Analog interface

This 15 pole D-sub socket on the rear side of the device is provided for remote control

of the device via analog or digital signals.
If remote control is in operation this analog interface can only be used alternately to

the digital interface. However, monitoring is always available.
The input voltage range of the set values and the output voltage range of the monitor

values, as well as reference voltage level can be switched in the settings menu of the

device between 0-5 V and 0-10 V, in each case for 0-100%.

Figure 4 - Analog interface

1.9.10

“Share BUS” connector

The two BNC sockets (50 Ω type) labeled “Share BUS” form a digital, passed-through

Share bus. This bus is bidirectional and connects the bus master unit via “Share BUS

Output” to the next slave unit (“Share BUS Input”) etc., for use in parallel operation

(master-slave). BNC cables of suitable length can be obtained from us or electronics

stores.
Basically, all 10000 series are compatible on this Share bus, though only connection

of the same device type, i. e. power supply with power supply or electronic load with

electronic load is supported by the devices for master-slave.
For a PSB 10000 series device, different or identical PSB 10000 series models can

be used as slave units. A PSB 10000 device can furthermore be the master of PSBE

10000 devices.

Figure 5 - Share bus

1.9.11

“Sense” connector (remote sensing)

In order to compensate for voltage drops along the DC cables to the load or external

source, the Sense input (2 plugs included in delivery, one each for positive and nega-

tive pole) can be connected to the load resp. external source. The maximum possible

compensation is given in the technical specifications.

In a master-slave system it’s intended to wire remote sensing only

to the master which would then forward the compensation to the

slaves via Share BUS.

The Sense cover must be installed during operation, because

there can be hazardous voltage on the sense lines! Reconfigu

ration on the Sense connectors is only permissible if the device

is disconnected from AC supply and all DC sources!

Figure 6- Remote sensing connectors

Содержание PSB 10000 4U















































































































Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды

EPS PSB 10000 4U, Руководство по эксплуатации

Результаты поиска

Содержание PSB 10000 4U

Отзывы:

Похожие инструкции для PSB 10000 4U

Бренды по названию

Популярные бренды