Epple Maschinen PW 30 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 50

background image

Stand 31.07.08, PW 30, PW 30 HV, Profile roll

Page 25 of 50

5 Bending

5.1

Bending instruction

Apply the material so that all 3 rolls are
touched at the same time (Pic 1).
Observe that the material lays parallel to the
bottom.
This position is called

„0-position“

Pic. 1

Move the upper rolls downwards (Pic. 2).
Adjust it the way you have to use the power
that is necessary to bend the material.
If are too powerful, you may damage the
material and do not achieve the desired
bending radius.

Pic. 2

You can move the rolls forwards and back
with the foot pedal (Pic. 3) to achieve in a few
runs the correct bending radius.
If the bending radius becomes too large,
move the upper roll downwards and repeat
the working actions.
If the bending radius becomes too small,
move the upper roll upwards and repeat the
working actions.

Upper roll

Lower rolls

Pic. 3

«
...
23
24
25
26
27
...
»

Содержание PW 30



















































Отзывы:

Нет отзывов

Похожие инструкции для PW 30

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Бренд: THORLABS Страницы: 44

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: Baileigh Industrial Страницы: 40

Бренд: CAMAG Страницы: 40

Бренд: Raven Страницы: 17

Бренд: Campbell Страницы: 12

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Qlight Страницы: 4

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: CAB Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды