EPOX EP-BX6 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 77

EPOX EP-BX6 Скачать руководство пользователя страница 12

Introduction

EP-BX6

Page 1-6

I/O Shield Connector

The EP-BX6 is equipped with an I/O back panel. Please use the appropriate I/O
shield (figure 3).

ATX
POWER SUPPLY

Power-On/Off (Remote)

The EP-BX6 has a single 20-pin connector for ATX power supplies. For ATX
power supplies that support the Remote On/Off feature, this should be connected
to the systems front panel for system Power On/Off button. The systems power
On/Off button should be a momentary button that is normally open.

The EP-BX6 has been designed with “Soft Off" functions. You can turn Off the
system from one of two sources: The first is the front panel Power On/Off the
button, and the other is the "Soft Off" function (coming from the EP-BX6’s
onboard circuit controller) that can be controlled by the operating system.
Windows 95/98 will control this when the user clicks that they are ready to
Shutdown the system.

Figure 4: Case (chassis) Power ON/OFF button

Figure 3: I/O back panel layout

J3

PS/2 Mouse

PS/2 Keyboard

Parallel Port

COM1

USB

COM2

(J3: PW-ON)

«
...
10
11
12
13
14
...
»

Содержание EP-BX6














































































Отзывы:

Нет отзывов