epiphan video Standalone VGA Grid Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 319

background image

Standalone VGA Grid User Guide

Configure DHCP

Label

Description/Options

Current IP Address

Reflects the current internet protocol address (IP address) of the system. This
value is either obtained from the DHCP server (if using DHCP) or is the configured
static IP address. The Standalone VGA Grid supports IPv4 addresses. It does not
support IPv6 addresses.

Configure DHCP

Occasionally, such as when moving your system to a new network, your Standalone VGA Grid must switch
from static IP address allocation to dynamic allocation via DHCP. You can accomplish this in four ways:

l

Restore factory settings, clearing all your custom settings. See

Perform factory reset

.

l

Load a configuration file that uses DHCP networking. See

Load a saved device configuration

.

l

Apply a configuration preset that uses DHCP networking. See

Configuration presets

.

l

Change the network settings. See the procedure below.

To configure use of DHCP for networking:

1. Connect to the admin interface using your preferred connection mechanism. See

Connect to the admin

2. Login as admin.

3. Select the

Network

link in the Configuration menu; the network configuration page opens.

4. Select the radio button

use DHCP

, if not already selected.

5. Change the

MTU Size

value only if needed. See the table below for information on maximum

transmission unit (MTU) values.

6. Click

Apply

to save the changes; the changes are saved and a message appears asking you to reboot.

7. Select the

Maintenance

link under the Configuration menu; the maintenance page appears.

8. Click the

Reboot Now

button near the bottom of the page.

9. Wait for the system to reboot.

10. Connect to the admin interface using your preferred connection mechanism. See

Connect to the admin

47

«
...
45
46
47
48
49
...
»

Содержание Standalone VGA Grid
































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Standalone VGA Grid

Бренд: Samson Страницы: 40

Бренд: XINDAK Страницы: 9

Бренд: Faroudja Страницы: 15

Бренд: IAdea Страницы: 15

Бренд: IAdea Страницы: 6

Бренд: Odys Страницы: 31

OMX-HDMI-HDB1X8

Бренд: Ocean Matrix Страницы: 6

Бренд: Rane Страницы: 2

MPC22017 - Portable Cd Player

Бренд: Magnavox Страницы: 1

Бренд: Broadcast Tools Страницы: 10

Бренд: VIORE Страницы: 49

Infinity IEC-2001

Бренд: LevelOne Страницы: 2

Бренд: Cosel Страницы: 62

Бренд: Clever Little Box Страницы: 56

Бренд: Marantz Страницы: 77

Бренд: MyMusix Страницы: 33

MediaServer MS5000

Бренд: Imerge Страницы: 68

Бренд: Lindy Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды