manualshive.com logo in svg

epiphan video Pearl Mini, Руководство пользователя

Поделиться
Скачать
epiphan video Pearl Mini Скачать руководство пользователя страница 324

Pearl Mini User Guide

Adjust latency and view the SRT stream status

9. (Optional) In the

Latency

field adjust the amount of latency to apply to the stream. The default

value is 125 ms.

We recommend using the default latency and recovery bandwidth overhead values for
an initial test stream. After you perform a test stream, you can determine the Quality of
Service (QoS) and calculate the latency requirements. To set the SRT stream latency, see

Adjust latency and view the SRT stream status

.

10. (Optional) In the

Recovery bandwidth overhead

field, adjust the % value of the bandwidth that's

dedicated for SRT control and recovery packets. The default value is 25%.

11. (Optional) Rename the stream. Click the current name and enter a different name, then press

Enter

.

Refresh your browser if the new stream name doesn't immediately display.

12. Click

Apply

.

13. When your ready to start streaming, click

Start

What's next?

If you also need to set up Pearl Mini as an SRT destination and ingest an SRT stream from a remote
source, you must add the SRT stream as a input, see

Connect an SRT stream as an input

.

Adjust latency and view the SRT stream status

Secure Reliable Transport (SRT) achieves high-quality, low-latency streaming across unreliable Internet
connections via UDP packets. If packets are lost in transit to the SRT destination, a request to retransmit
the lost packets is sent back to Pearl Mini. Using the Admin panel, you can adjust the latency to improve
the Quality of Service (QoS) of the stream and reduce the number of dropped packets.

During the SRT stream, you can view the stream statistics using the Admin panel and adjust the amount
of latency based on the packet loss % and Round Trip Time (RTT). SRT stream statistics are provided on
the streaming configuration page for a channel when Pearl Mini is configured as an SRT source. If Pearl
Mini is configured as an SRT destination with an SRT input, then SRT statistics are available on the SRT
input configuration page.

The following example shows SRT statistics for an SRT stream. The statistics section appears only while an
SRT stream is active. It takes about 30 seconds for the statistics to appear after the SRT connection is
established.

313

Содержание Pearl Mini



































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды