16
HOW TO TURN ON THE POWER
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 14). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Start/Stop button for a few seconds.
If the displays remain lit, see THE INFORMATION
MODE on page 26 to turn off the demo mode.
Next, stand on the foot rails
of the treadmill. Locate the
clip attached to the key (see
the drawing at the right),
and slide the clip securely
onto the waistband of your
clothes. Then, insert the key
into the console. After a moment, the displays will light.
IMPORTANT: In an emergency situation, the key
can be pulled from the console, causing the walk-
ing belt to slow to a stop. Test the clip by carefully
taking a few steps backward; if the key is not
pulled from the console, adjust the position of the
clip.
IMPORTANT: If there is a sheet of clear plastic on
the face of the console, remove the plastic. To pre-
vent damage to the walking platform, wear clean
athletic shoes while using the treadmill. The first
time the treadmill is used, observe the alignment
of the walking belt, and center the walking belt if
necessary (see page 30).
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE INFORMATION MODE on page
26. For simplicity, all instructions in this section refer to
miles.
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
Each time the key is in-
serted, the manual mode
will be selected. If you
have selected a workout,
press any of the workout
buttons repeatedly until a
track appears in the matrix.
3. Start the walking belt and adjust the speed.
To start the walking belt, press the Start/Stop but-
ton, one of the Speed increase buttons, or one of
the speed buttons numbered 1 to 12.
If you press the Start button or one of the Speed
increase buttons, the walking belt will begin to
move at 1 mph. As you exercise, change the
speed of the walking belt as desired by pressing
the Speed increase and decrease buttons on the
console or in the right handrail. Each time you
press a button, the speed setting will change by
0.1 mph; if you hold down the button, the speed
setting will change in increments of 0.5 mph. If you
press one of the numbered speed buttons, the
walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Start/Stop but-
ton. To restart the walking belt, press the
Start/Stop button, one of the Speed increase but-
tons, or one of the numbered speed buttons.
4. Change the incline of the treadmill as desired.
To change the incline of the treadmill, press one of
the Incline increase or decrease buttons or one of
the incline buttons numbered 0 to 12.
Each time you press one of the Incline increase or
decrease buttons on the console or in the left
handrail, the incline will change by 0.5%. If you
press one of the numbered incline buttons, the in-
cline will gradually change until it reaches the se-
lected incline setting. Note: After you press the but-
tons, it may take a moment for the treadmill to
reach the selected incline setting.
Reset
Clip
Key
