Eoslift H10 Скачать руководство пользователя страница 4

01

02

Figure1

Rated capacity

Load center

Dead-weight

Minimum fork height

Maximum fork height

Lowered Mast Height

Fork length

Overall fork width

Length of the stacker

Width of the stacker

Load-bearing wheel

Steering wheel

Minimum turning radius

1000       

H10       

H15

kg

mm

kg

mm

mm

mm

mm

mm

mm

mm

mm

kg

H20

1500       

2000       

600

270

-

320

85

1600/2500/3000

2030/1780/2030

1600

2030

1600

2030

1150  

540/330-740  

1670  

764/834  

Φ

70×70  

Φ

180×50  

1295  

6

.  

Operation protection

Hands and feet shall be kept far away from moving parts, such as frame, chains, forks and wheels to prevent 
pinching hands.

5

.  

Safety device and warning signs

Safety device, warning signs and the above safety precautions must be given enough attention to.

When handling the goods, the fork height must not exceed 300mm.

4

.  

Hazardous area

The hazardous area usually refers to the area where the stacker or its lifting device (e.g. forks, attachments) 
will pose threat to persons during their operation or lifting process. Typically, this range extends to the area 
where goods or stacker accessories are lowered.

Unauthorized persons must leave the hazardous area. Whenever a situation causes possible harm to 
persons, the operator must give a warning.  If the unauthorized persons still stays in the hazardous 
area after the waring is given, the operator must immediately stop the operation of the stacker.

Warning

3

.  

Faults and defects

If stacker failure or defects occur, immediately notify the management personnel. If the stacker is not safe 
for operation (such as wheel worn or brake failed, etc.), please stop using it before it is fully repaired.

2

.  

   

Free from rainwater or corrosion of harmful gases;

    Room temperature of -20°C~+40°C;
    Relative ambient humidity <90%;
    Requirements for ground: hard, anti-skid and level without barriers.

The stacker is only applicable to indoor use and the application environment must meet the 
following conditions:

1

.  

Requirements for operator

The stacker must be operated by persons trained in operation. The operator shall be able to carry out 
operation demonstration of moving and controlling goods for users, and he or she is responsible for the 
stacker.Unauthorized persons are not allowed to operate the stacker. Do not carry or lift passengers.

Technical parameters

Model

Safe operating rules

H10

/

15

/

20 

Series Manual Pallet Stackers

Содержание H10




















Отзывы: