BENEFITS
Helps provide relief from allergy, asthma and other
respiratory illness.
Helps clear a smoky environment quickly, so everyone
can work and relax together.
Helps reduce the time and money spent on cleaning and
redecorating. Prevents damaging black dust from
staining walls, upholstery and window coverings.
Improves indoor air quality for a fresher, more
comfortable environment, year-round.
HOW IT WORKS
Dirty air is drawn in through the front grill and passes through
a 4-Stage filtering system.
The Electrostatic Prefilter is constructed of a close knit poly
mesh. It prevents larger particles from entering the collecting
cell.
The next step is a 2-Stage Electrostatic Collecting Cell. The
dirt particles are charged with a high positive voltage by a
series of fine ionizing wires. The charged particles are drawn
through to the collecting plates where the dirt adheres to the
grounded plates and remains until the cell is taken out and
washed. Removes particles down to .01 micron (1/2,540,000
of an inch).
The air is then drawn through an Activated Carbon/
Potassium Permanganate VOC (Volatile Organic Compound)
Filter for removal of odors and gases emitted from carpets,
cabinets, glues, household cleaners, paints, varnishes,
solvents, personal care products, tobacco and cooking
smoke, and lots more. Clean air is then discharged out the
top and back of the Air Cleaner.
A Negative Ionizer needle, controlled by a separate switch, is
located in the clean air stream. Adding negative ions to the
air revitalizes the air similar to that near a waterfall, spring,
ocean, or after a rainfall. Studies have shown that negative
ions have a beneficial effect on human biochemistry, both
physically and mentally.
OPERATING INSTRUCTIONS
1. Remove all packaging from the unit. Choose a suitable
location to allow unobstructed circulation from front, top
and back of unit. The unit performs best when the back
is against a wall. This enhances air circulation. Allow at
least one inch (2.5 cm) away from back wall.
Note: Do not place Air Cleaner in direct sunlight.
2. Operate Air Cleaner at voltage shown on back of unit.
3. The controls for the Air Cleaner are located on the front
panel. To turn the Air Cleaner on, push the System
Switch to the
ON
position. This controls the power to the
Fan Speed Switch and to the power board. When the
Fan Speed Switch is in the extreme right position, the
fan is on low; center position is medium; and to the left is
high speed. When the System Switch is turned
ON
, the
green Performance Indicator Light should be illuminated.
4. The rocker switch located next to the red LED, controls
the negative ion emitter. When the switch is on, the red
light will illuminate.
Note: The Negative Ion Emitter will not work without
the System Switch being ON.
Odor & Gas (VOC) Filter*
Collecting Cell
Air Flow Direction
Arrow
Electrostatic Prefilter
Access Door
* Grey foam side must
face to rear.
You may notice a slight heat odor when new unit is first
turned on. This is normal and will disappear within a 24 hour
period.
We recommend the Air Cleaner be run on low or medium
speed for quiet, continuous or nighttime use. Use the high
speed for initial cleaning of heavy concentrations of dirty air
(i.e. smoke) or after leaving the room.
You may notice arcing or snapping from the cell. It is normal
to hear some arcing when the unit is new or first turned on.
Arcing in the cell may also be caused by high humidity (over
80%), after washing, or when a large particle of dirt or hair is
caught in the cell. If the arcing is continuous and constant,
then refer to the Troubleshooting Chart.
1 Dirty Air
2 Prefilter
3 Charging
Section
4 Collecting Cell
Plates
5 Odor & Gas
Filter
7 Negative Ions
and Clean Air
6 Ionizing Needle
ON OFF
High Speed Medium Speed Low Speed
Negative Ion Switch Fan Speed Switch System Switch