manualshive.com logo in svg

Enviro 828 DV.FS., Руководство пользователя

Поделиться
Скачать
Enviro 828 DV.FS. Скачать руководство пользователя страница 8

5. INSTALLING BURNER CONTROL ASSEMBLY

 

 
Remove the controls from box, check for shipping damage. Remove burner 
tray from controls (one screw on each side between burners). 
 
Open door.  Remove grate rod by pulling up at each end.  Remove the 2 
screws behind the grate and one screw on each side of control opening in 
firebox. 
 
Extend flex gas line and place through hole in center of pedestal (freestanding 
and inserts) or through hole in right or left firebox side (insert only).  Lower the 
controls into place at the back while pulling the flex line through on other side.  
Lower front into place, the control knob may need to be pushed in to allow 
burner controls to fit. 
 
Install the two side screws, then install the front screws through the grate into 
the firebox.  Replace burner tray. 
 
Install the grate rod and logset. 
 

6. INSTALLATION OF LOG SET and EMBERS

 

Upon the first light up, watch for ignition to 

all

 burner 

ports.  If a long delay is noted: 

 

a) First, wait for the appliance to cool down 
b) Open the front door of the appliance. 

 
c) Checks to Carefully reposition the embers making sure 

that burner ports are not plugged solid or blocked 

 

 
 

CAUTION: NEVER OPERATE THIS APPLIANCE WITH THE 

DOOR REMOVED 

 

 

INSTALLING THE LOG 

a. INSTALLING THE GLOWING EMBERS 

 

 

Carefully remove log from unit.  Check to ensure there is 
no damage.  It is very important to install this log in its 

proper position to insure safe optimum operating 

conditions. 

A bag of ceramic fiber embers is provided for use on the 

front burner ember tray. 
 

CAUTION:  Use only the type of ember material supplied 
with this appliance.  Due to the irregular size of the ember 

material there may be more than required.  Use only a 

single layer.  Do not pile embers.  The use of other foreign 
materials on the burners may create dangerous 

conditions. 
 

If over time, through cleaning and servicing, these embers 
require replacement, contact your nearest ENVIROGAS 

dealer for replacement embers. 
 

Gently remove the ember material from the plastic bag.  

Spreading these pieces evenly across the front of the 
ember tray.  Place a single layer of embers on top of the 

front burner.  Carefully avoid any clumping or large build-
ups. 

 
 

 

 

 

Do not pack down, leave embers loose. 

1.  Open the front door. 

 

 

 

DO NOT PLACE EMBERS ON THE REAR BURNER. 

8

Содержание 828 DV.FS.


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды