Enviro 828 DV.FS. Скачать руководство пользователя

Страница: 1 / 25

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY

THIS MANUAL IS PRINTED ON RECYCLED PAPER

8 2 8

B y S H E R W O O D I N D U S T R I E S L T D .

D i r e c t V e n t

O W N E R S M A N U A L

Installation And Operating Instructions For Models:

828 MH (MOBILE HOME)

828 DV. FS. (Freestanding)

828 DV. INS. (Insert)

WARNING

If the information in this

manual is not followed exactly,

a fire or explosion may result

causing property damage,

personal injury or loss of life. A

qualified installer, service

agency or the gas supplier

must perform installation and

service.

WHAT TO DO IF YOU SMELL GAS

•

Open windows/Extinguish any open flame

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any

phone in your building.

•

Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's
instructions.

•

If you cannot reach your gas supplier, call the fire

department.

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY

Do not store or use gasoline or other Flammable vapors and liquids

in the vicinity of this or any other appliance.

Содержание 828 DV.FS.


























Результаты поиска

Содержание 828 DV.FS.

Отзывы:

Похожие инструкции для 828 DV.FS.

Бренды по названию

Популярные бренды

Enviro 828 DV.FS., Руководство пользователя

Результаты поиска

Содержание 828 DV.FS.

Отзывы:

Похожие инструкции для 828 DV.FS.

Бренды по названию

Популярные бренды