background image

                                                                                                                                       

Service  and  Installation  Manual

 

2           

For warranty service, call 866-417-6140                                                       

CONTENTS

 

                                                                             

 

RECEIVING  &  INSPECTING  EQUIPMENT………………………………………..…………………2 

SPECIFICATIONS

…………………………………………………….……………………….………3 

INSTALLATION

………………………………………………………………………….…………..….4 

OPERATION………..……………………………………………………………………..……………5 

MAINTENANCE

……………………………………………………………………….……………….7 

All rights reserved. Reproduction without written permission is prohibited. 

Is a registered trademark of Entrée L.L.C. 

 

SERIAL NUMBER INFORMATION                                                                               

The serial number of all self-contained refrigerators and freezers is located inside the unit on the left hand 
side near the top on the inside wall. 

Always have the model and serial number of your unit available when calling for parts or service. 

This manual covers standard units only. If you have a custom unit, consult the customer service department 

at the number listed on the last page. 

RECEIVING AND INSPECTING THE EQUIPMENT                                             

Even though most equipment is shipped crated, care should be taken during unloading so the equipment is not 
damaged while being moved into the building. 

1.  Visually inspect the exterior of the package and skid or container. Any damage should be noted and reported 

to the delivering carrier immediately. 

2.  If damaged, open and inspect the contents with the carrier. 
3.  In the event that the exterior is not damaged, yet upon opening, there is concealed damage to the equipment, 

notify the carrier. Notification should be made verbally as well as in written form. 

4. Request an inspection by the shipping company of the damaged equipment. This should be done within 10 

days from receipt of the equipment. 

5. Be certain to check the compressor compartment housing and visually inspect the refrigeration package. Be 

sure lines are secure and base is still intact. 

6. Freight carriers can supply the necessary damage forms upon request.   
7. Retain all crating material until an inspection has been made or waived. 

 

 

 

 

 

 

 

Содержание BB-1HD













Отзывы: