Entone Janus 300 Series, Руководство по установке, Страница: 13 / 14

SE
TUP GUIDE
JANUS MEDIA HUB
SE
TUP GUIDE
JANUS MEDIA HUB
DECLARATION OF CONFORMITY
23
Declaration of Conformity (Europe Only)
This product is in conformity with the Council Directives:
• EMC Directive 2004/108/EC
• Low voltage Directive 2006/95/EC
Canada Certification Notice
ICES-003 Class B Notice
This Class B digital apparatus complies with Canadian ICES-003.
Avis NMB-003, Classe B
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective operations and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The
department does not guarantee the equipment will operate to the user’s satisfaction. This equipment
meets the applicable Industry Canada Terminal Equipment Technical Specification. This is confirmed by
the registration number. The abbreviation, IC, before the registration number signifies that registration
was performed based on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the equipment. The Ringer
Equivalence Number (REN) is 0.0. The Ringer Equivalence Number that is assigned to each piece of
terminal equipment provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed 5.0. Before installing this equipment, users should ensure that it is permissible
to be connected to the facilities of the local Telecommunication Company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that compliance
with the above conditions may not prevent degradation of service in some situations. Connection to a
party line service is subject to state tariffs. Contact the state public utility commission, public service
commission, or corporation commission for information. If your home has specially wired alarm
equipment connected to the telephone line, ensure that the installation of this equipment does not
disable your alarm equipment. If you have questions about what will disable alarm equipment, consult
your telephone company or a qualified installer. If you experience trouble with this equipment, do not
try to repair the equipment yourself. The equipment cannot be repaired in the field and must be
returned to the manufacturer. Repairs to certified equipment should be coordinated by a
representative, and designated by the supplier. Users should ensure, for their own protection, that the
electrical ground connections of the power utility, telephone lines, and internal, metallic water pipe
system, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electrical inspection authority, or electrician, as appropriate.
22
DECLARATION OF CONFORMITY
To ensure proper use of this product, please read this manual carefully and retain it for future reference.
Should the unit require maintenance, contact an authorized service location.
WARNING: This symbol indicates the presence of uninsulated dangerous voltage within the product's
enclosure that constitutes a risk of electric shock. Do not open the product's case.
CAUTION: This symbol indicates you must take care; there is risk of damage to the equipment or
to yourself.
To prevent fire or shock hazard, do not expose this product to rain or moisture. To reduce the risk of
electric shock, DO NOT remove the cover or back. No user serviceable parts are inside. For servicing refer
to qualified personnel.
Declaration of Conformity (United States Only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal
Communication Commission (FCC) Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF and ON, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to a different circuit from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Part 68 - Compliance Registration
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. A
label on the bottom of this equipment contains, among other information, the Ringer Equivalence
Number (REN) and the product identifier. For products approved after July 23, 2001 the product
identifier is in the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a
decimal point (e.g. 03 is a REN of 0.3). The REN is used to determine the number of devices that may be
connected to a telephone line. For earlier products, the REN is separately shown on the label. If
requested, this number must be provided to the telephone company. Excessive RENs on a telephone
line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the
sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected
to a line, as determined by the total RENs, contact the local telephone company. This equipment is
designed to connect to the telephone network or premises wiring using a compatible modular jack that
is Part 68 compliant. An FCC compliant telephone cord and modular plug is provided with the
equipment. If this terminal equipment causes harm to the telephone network, the telephone company
may request you to disconnect the equipment until the problem is resolved. The telephone company
will notify you in advance if temporary discontinuance of service is required. If advance notification is
not practical, the telephone company will notify you as soon as possible. You will be advised of your
right to file a complaint with the FCC if you believe such action is necessary. If you experience trouble
with this equipment, do not try to repair the equipment yourself. The equipment cannot be repaired in
the field. Contact your ISP for further instructions. The telephone company may make changes to their
facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this
happens, the telephone company will provide advance notice in order for you to make the modifica -
tions necessary to maintain uninterrupted service. If your home has specially wired alarm equipment
connected to the telephone line, ensure that the installation of this equipment does not disable your
alarm equipment. If you have questions about what will disable alarm equipment, consult your
telephone company or a qualified installer. This equipment cannot be used on public coin phone
service provided by the telephone company. Connection of this equipment to party line service is
subject to state tariffs.