3
4
5
INSTALLING THE MODULE
Handling the Module
To prevent electrostatic damage, observe the following guidelines:
•
Do not remove the module from its packaging until you are ready to
install it.
•
Do not touch any of the module’s pins, connectors or components.
•
Hold the module only by its edges or front panel.
•
Wear an anti-static wristband connected to a suitable earth ground whenever handling
the module.
•
Store or transport this module only in appropriate anti-static packaging.
Equipment Checklist
After unpacking the ER16-SERC-04-AA, check the contents of the box to be sure you
received the following items:
•
One ER16-SERC-04-AA module in anti-static bag
•
One disposable anti-static wristband
Tools
This installation requires the following tool:
Preliminary Setup
Firmware Image Requirements
Version 8.3.0.0 or later.
CLI Setup
Enter the following command at the CLI before implementing any configurations.
1.
Type the following from Enable mode to enter Configuration mode
Enable -> Configure #
2.
You may now begin configuring ports on the ER16-SERC-04-AA. Refer to the
Enterasys X-Pedition Command Line Interface Reference Manual for details.
Hotswap
You may install this module into a live system without powering off the device. However,
you may not remove an active module from a live system except under the following
conditions:
•
Press the Hotswap button. The Online LED will turn off and the Offline LED will
turn on.
OR...
•
Enter the following from the CLI and click enter: Enable -> System -> Hotswap ->
Out -> Slot -> #. The Online LED will turn off and the Offline LED will turn on.
Instructions
1.
If a coverplate is installed in the slot where you will install the ER16-SERC-04-AA,
remove the coverplate: loosen the screws on the ejectors until the screws pop out,
then open the ejectors and pull out the plate.
2.
Open the ejectors at the top and bottom of the ER16-SERC-04-AA.
3.
Align the metal backpanel with the card guides at the top and the bottom of the slot
opening, as shown in
Figure 1
.
4.
Slide the ER16-SERC-04-AA all the way into the slot, firmly but gently pressing to
ensure that the pins on the back of the module are completely seated in the backplane.
5.
To lock the ER16-SERC-04-AA into the slot, close the ejectors. Using a flathead
screwdriver, tighten the screw on each ejector.
Figure 1
Install the ER16-SERC-04-AA
TROUBLESHOOTING
Proper Boot Sequence
•
Firmware loads.
•
The control module for the chassis should indicate that the ER16-SERC-04-AA was
detected and is operating correctly.
•
The Online LED will turn on and remain lit (no other LEDs should illuminate during
module power-up).
Common Errors
•
The ER16-SERC-04-AA is not inserted properly or seated completely in the chassis
•
Connectors for the connected lines are not seated properly.
Helpful CLI Commands for Debugging
•
System show hardware
•
System show version
•
Port show port status se.x.y (where x is the chassis slot that contains the line card
and y is a specific port number on the card).
•
System show bootlog
ADDITIONAL INFORMATION
For additional information about installing this module or to learn more about what
capabilities are included in the firmware release you are using, visit the Enterasys
Networks web site.
Getting Help
For additional support related to the Common CLI syntax or this document, contact
Enterasys Networks using one of the following methods:
Before contacting Enterasys Networks for technical support, have
the following information ready:
•
Your Enterasys Networks service contract number
•
A description of the failure
•
A description of any action(s) taken to resolve the problem (e.g., changing mode
switches, rebooting the unit)
•
The serial and revision numbers of all involved Enterasys Networks products in the
network
•
A description of your network environment (layout, cable type, etc.)
•
Network load and frame size at the time of trouble (if known)
ELECTRICAL HAZARD: Only qualified personnel should perform
installation procedures.
CAUTION: The ER16-SERC-04-AA is easily damaged by
electrostatic discharge.
Anti-static wristband
Flathead screwdriver
CAUTION: Before performing any upgrade or installation, ensure
that you are properly “grounded” to avoid electrostatic discharge. The
switch must be powered off before installing or replacing any module.
NOTE: Make sure that the metal backpanel of the
ER16-SERC-04-AA—not the circuit card—is between the card
guides. Check both the upper and lower tracks.
Rotate ejector
to lock in place
Metal
Backpanel
Card
Guides
Circuit Card
TX RX LINK
1
2
ONLINE
OFFLINE
HOT
SWAP
World Wide Web
http://www.enterasys.com/
Phone
(603) 332-9400
Internet mail
FTP
Login
Password
ftp://ftp.enterasys.com
anonymous
your email address
To acquire the latest image for
this product and any available
release notes
http://www.enterasys.com/download
Additional documentation
http://www.enterasys.com/support/manuals
To send comments or suggestions concerning this document, contact the
Technical Writing Department via the following email address:
[email protected]
Please include the document Part Number in the email message.
ER16-SERC-04-AA
Quick Start
Web Site:
http://www.enterasys.com/
9033749
