Ensemble Designs BrightEye 55 Скачать руководство пользователя страница 10

Страница: 10 / 26

BrightEye 55 Genlockable SPG/TSG

BrightEye 55 - Page 10

HD Sync

The currently selected HD Tri Level Sync format (

1080i

720p

1080p

, or

1080sF

)

is illuminated green. One of two different Tri Level Sync (TLS) frame rates can be
selected in the

Config

menu of the BrightEye Control application as

23.98/50/59.94

(the most commonly used, default value) or

24/30/60

(for special

applications such as film).

Pwr (Power)

Illuminates green when power is applied to the unit and the internal voltage
regulator is functioning correctly.

ADJUSTING PARAMETERS FROM THE FRONT PANEL

Use the

Mode

Right Arrow,

and

Left Arrow

buttons to select and adjust

parameters from the front panel.
Pressing the

Mode

button activates the front panel for editing and tabs between

each section of editable parameters.
Pressing the

Right Arrow

Left Arrow

advances the selection within a given

section of parameters, or increases (Right Arrow) or decreases (Left Arrow) the
value of a selected parameter.

The LED of an edited parameter will blink for 15 seconds, after which time its value is
stored in memory. If power is interrupted before this 15 second timeout period has
elapsed, the edited state will not be not saved.

The LED indicators will report the following:

• Std (Standard) select

– currently selected video output standard

blinks.

• Ref

– illuminates green when a valid NTSC or PAL reference is

detected. Off when no reference is detected.

• Video

– currently selected video pattern (or pattern group) output

blinks.

• Slate on/off

– blinks quickly when ID slate is enabled, slowly when

disabled.

• Tone on/off

– blinks quickly when tone is enabled, slowly when

disabled.

• HD Sync select

– currently selected HD Tri Level Sync format

blinks.

The controls and their indicators are described below:

Std (Standard)

This control selects the video output standard with the following choices:

NTSC

– 525 NTSC standard

PAL –

625 PAL standard

NOTE

Содержание BrightEye 55



























Результаты поиска

Содержание BrightEye 55

Отзывы:

Похожие инструкции для BrightEye 55

Бренды по названию

Популярные бренды

Ensemble Designs BrightEye 55, Руководство пользователя

Результаты поиска

Содержание BrightEye 55

Отзывы:

Похожие инструкции для BrightEye 55

Бренды по названию

Популярные бренды