ENS SIP46B5/28-H Скачать руководство пользователя страница 69

Страница: 69 / 197

Network Camera User Manual

TCP/IP Settings

Configure the basic network settings, including the NIC Type, IPv4 or IPv6 Address,

IPv4 or IPv6 Subnet Mask, IPv4 or IPv6 Default Gateway, MTU settings and

Multicast Address.

(Optional) Check the checkbox of

Enable Multicast Discovery

, and then the online

network camera can be automatically detected by client software via private

multicast protocol in the LAN.

Configure the DNS server. Input the preferred DNS server, and alternate DNS

server.

Click

Save

to save the above settings

Notes



The valid value range of MTU is 1280 to 1500.



The Multicast sends a stream to the multicast group address and allows multiple

clients to acquire the stream at the same time by requesting a copy from the

Содержание SIP46B5/28-H






































































































































































































Результаты поиска

Содержание SIP46B5/28-H

Отзывы:

ENS SIP46B5/28-H, Руководство пользователя, Страница: 69 / 197

Результаты поиска

Содержание SIP46B5/28-H

Отзывы: