enphase IQ 7 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 43

background image

IQ 7 / IQ 7+ / IQ 7X / IQ 7A with EN4 Bulkhead Installation and Operation

© 2020 Enphase Energy Inc. All rights reserved.

141-00047-01

38

IQ7X-96-E-US Microinverter

Parameters

Topic

Unit

Min

Typical

Max

Miscellaneous Parameters

Maximum

9

microinverters per 20A (max) AC branch circuit

240 VAC (single phase)
208 VAC (single phase)

12
10

CEC weighted efficiency

240 VAC (single phase)
208 VAC (single phase)

%

97.5
97.0

Static MPPT efficiency (weighted, ref EN 50530)

%

99.0

Total harmonic distortion

%

5

Ambient temperature range



C

-40

+60

Night tare loss

mW

50

Storage temperature range



C

-40

+85

Features and Specifications

Compatibility

Pairs with 96-cell PV modules

Dimensions not including mounting bracket

212 mm x 175 mm x 30.2 mm (approximate)

Connector type

Enphase EN4 bulkhead

Weight

1.08 kg (2.38 lbs.)

Environmental category / UV exposure rating

NEMA type 6 / outdoor

Torque specifications for fasteners
(Do not over torque)

•

6 mm (1/4”) mounting hardware: 5 N m (45 - 50 in-lbs.)

•

8 mm (5/16”) mounting hardware: 9 N m (80 - 85 in-lbs.)

•

When using UL 2703 mounting hardware, use the
manufacturer’s recommended torque value

Cooling

Natural convection - no fans

Relative humidity range

4% to 100% condensing

Approved for wet locations

Yes

Pollution degree

PD3

Communication

Power line communication (PLC)

Standard warranty term

enphase.com/warranty

Compliance

CA Rule 21 (UL 1741-SA) UL 62109-1, UL1741/IEEE1547, FCC Part
15 Class B, ICES-0003 Class B, CAN/CSA-C22.2 NO. 107.1-01
This product is UL Listed as PV Rapid Shut Down Equipment and
conforms with NEC-2014 and NEC-2017 section 690.12 and C22.1-
2015 Rule 64-218 Rapid Shutdown of PV Systems, for AC and DC
conductors, when

installed according manufacturer’s instructions.

Grounding

The DC circuit meets the requirements for ungrounded PV
arrays in NEC. Ground fault protection (GFP) is integrated into
the class II double insulated microinverter.

Monitoring

Enlighten Manager and MyEnlighten monitoring options. Both
options require an Enphase IQ Envoy

Integrated DC disconnect/
Integrated AC disconnect

The DC and AC connectors have been evaluated and
approved for use as the load-break disconnect required by
NEC 690.

9

Limits may vary. Refer to local requirements to define the number of microinverters per branch in your area.

.

«
...
36
37
38
39
40
...
»

Содержание IQ 7












































Отзывы:

Нет отзывов

Похожие инструкции для IQ 7

Бренд: Manfrotto Страницы: 4

Бренд: TaylorMade Страницы: 5

Бренд: oliser Страницы: 6

Бренд: La Crosse Technology Страницы: 2

Бренд: Parkside Страницы: 89

Бренд: Parkside Страницы: 28

Бренд: UniFlow Страницы: 42

NNC994S - Genius Prestige - Convection Microwave...

Бренд: Panasonic Страницы: 1

Бренд: YachtSafe Страницы: 2

Бренд: Omron Страницы: 16

Бренд: Digisol Страницы: 18

Бренд: Carcomm Страницы: 2

Бренд: Whispbar Страницы: 14

Бренд: Deka Страницы: 4

BIS M-411-068-001-09-S72

Бренд: Balluff Страницы: 2

Бренд: REVCAMUK Страницы: 4

Бренд: SMC Networks Страницы: 80

Telaire Ventostat T8100 NS Series

Бренд: Amphenol Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды