TOC1306NUEN_0913
1/2
TRI
0
2
SYS
sarl –
grande rue le village, 21160 FLAVIGNEROT
1.1 Use
The detector
0
2
LINE
10020051
detects the presence (movement) of
persons. It forms an integral part of
the
TRI
0
2
SYS
radio system.
Its installation is fully wireless
because the presence detector has
solar cells with which it can supply
the energy necessary for its operation.
Note:
- No batteries or maintenance required!
- Read the operating manual carefully before initial use.
1.2 Guarantee terms
This operating manual is an integral part of the device and our guarantee terms.
It must always be delivered to the user. We reserve the right to modify the
technical design of these devices without warning.
TRI
0
2
SYS
products are
manufactured and their quality checked by making use of the latest technologies
and taking into account the applicable national and international directives. If
nevertheless a fault arises,
TRI
0
2
SYS
undertakes to remedy the default as
follows, without prejudicing the rights of the end customer that arise from the
sales contract with his reseller:
If the event of exercising of a legitimate and regular right,
TRI
0
2
SYS
, may at its
sole discretion, rectify the device fault or supply a fault-free device. Any claim
beyond this and all claims for consequential damages are excluded.
A legitimate fault exists if the device cannot be used at the time of delivery to the
end customer because of a design or manufacturing defect or if its practical use
is severely limited. The guarantee is void in cases of natural wear and tear,
incorrect use, incorrect connection, where the device has been repaired or
external influence. The period of guarantee is 24 months (from the date of
invoicing). French law applies to the regulation of guarantee rights.
1.3 Recycling of the device
To recycle the device, conform to the legislation and standards in force in the
country of use.
Observe the following points:
• The laws, standards and directives in force.
• Best practice at the time of installation
• The device operating manual.
• An operating manual can only give general instructions. They must be
interpreted in the context of a specific installation.
The device is intended solely for use conforming to its purpose. Any repairs or
modifications by the user are forbidden! Do not use with other devices the
operation of which could endanger people, animals or property.
Transmission frequency
868.3 MHz
Power supply
Solar cell (50-200 lux), optional
battery type CR2032 (<50 lux) or
external power supply 3-5V (DC)
Minimum charging time
20 minutes (>500 lux) or 5 minutes in a
well lit location with assistance
Time for complete charging
9h at 200 lux
Operating time in total darkness
48h (after complete charging)
Detection range
12 m diameter
Endurance without assistance
(in stand-alone operation)
•
Standard luminosity
15 years (200 lux for 2h/day, 5d/week)
•
Low luminosity
10 years (50lux for 5h/day, 7d/week)
•
Total darkness
5 years
EnOcean Profile Equipment
A5-07-01
Installation height
2 to 3m (recommended)
Operating environment
-10° to 40°C, 20 to 95% relative
humidity (without condensation)
Marking
CE and R&TEE directive 1999/5/CE
Size and weight
160x60x37mm / 125g
Masonry
20m, through 3 walls at most
Reinforced concrete
10m, through 1 wall/ceiling at most
Plasterboard / wood
30m, through 5 walls at most
Note: The signal strength between the detector and the receiver decreases as
the distance increases. Where there is a line of sight connection, the range is
approximately 30 m in corridors and 100 m in large workshops or halls. The
range can be increased with an
0
2
LINE
repeater.
Take the required time to verify each of the points below to ensure optimum
operation of the detector with all of the other installation components.
4.1 Installation instructions
Withdraw the sensor from its packaging and place it in daylight for 20 minutes to
provide it with the required start-up power; if necessary install a CR2032 type
battery for five minutes in a well lit location.
▪
Ensure that the location provides adequate coherent light
▪
Position the sensor between 2 and 3 meters from the ground
▪
Avoid installing the detector close to a ceiling fan or suspended luminaires
▪
Take into account the use of the zone to be surveyed (traffic, work, rest, etc.)
▪
Allow for a minimum clearance of one metre from all heat sources (light bulbs,
convection air currents, ventilation systems, etc.)
▪
Identify the construction materials (metal, wall) in the detection zone which
could interfere with the RF signals.
A single occupation sensor provides adequate coverage for most
zones. However in certain situations, several sensors may be necessary to
ensure complete coverage.
4.2 Installation
The presence detector can be installed on most ceilings with single screws (not
supplied).
Detection cone
:
1. Decide where to install the presence detector.
2. Position the detector using a double glue line (not supplied) and use the test
modes (see section 5.2) to determine if the selected location is suitable
3. Remove the sensor from the support (1)
4. Use the support as a template to mark holes for drilling
5. Drill holes for 5mm wall plugs
6. Fix the support with screws (not supplied)
7. Slide the detector on to the support until it engages
NOTE: It is often easier to associate the detector with its receiver before it is
mounted on the ceiling.
4.3 Association
To associate or disassociate the detector:
1. Place the desired receiver in learn mode (refer to the installation guide for
this device).
2. Press once on the detector's LRN button.
The
10020051
detector transmits the presence information using the frame
described in the document EnOcean Equipment Profiles EEP §A5-07-01
(consultable under
www.enocean.com
).
Button
LRN
Button SET
(illuminated surface)
2. Safety
3. Technical characteristics
General characteristics
Installation and operating manual
EnOcean ceiling mounted presence detector
Ref. 10020051
EN
Range in buildings
4. Installation and initial use
5. Functions and
options
1
1. General
0
3 m
0 0.3 0.9 1.4 2.3 2.8 3.3 4 4.3 5.1 m
