after 10 seconds after pressing the button ON or
OFF).
Possible error states in multi-button modes are signa-
led accoustically (2 beeps) and a red flashing of LED
and
:
Activity before signa-
ling the error state
Cause of the error state
Pressing the button
ON or OFF
No numerical button was
pressed before pressing
(nothing to be transimitted)
Pressing the button
ESC
No numerical button was
pressed before pressing
(nothing to delete)
Pressing the numeri-
cal button
If there is a mistake pres-
sing the combintaion of the
4-button code, the entire
entry is deleted, and you
must start the input again.
Delay between the
pressing of two but-
tons
More than 5 sec elapsed
since the last pressing of
the numerical button, the
entire entry is deleted
The transmitted code in multi button mode includes
information about which button (ON or OFF) has been
pressed. The receiver evaluates this information,
which means that a single numerical code can control
associated functions such as ON + OFF, TIMER +
OFF and function JAL, ROLL and DIMM in two button
mode.
Ongoing transmission of a coded signal is indicated
by a green flashing LED
while the button is
pressed.
The duration of code transmission, in case of a
permanent pressed button, is limited to 60 s.
FIRST USE
The transmitting keyboard is possible to lay freely or
to mount on a suitable area with stickers, which come
in the package.
The transmitting keyboard is factory preset to the mul-
ti button mode. The mode can be changed in the
setting mode.
Entering the setting mode is protected from unautho-
rized manipulation with a 4-digit password (preset
password is 1234).
Change mode
Press the button ON, OFF and ESC at the same time.
It is indcated by the red flashing LED .
Choose 1 4-digit password and press the button ON
for confirmation. The green LED starts illuminating.
The actual mode of the keyboard is signalized by LED
.
If the LED is not shining it is indicates one button
mode. If LED
is flashing green it indicates multi
button mode and if LED
is illuminated green it
indicates multi button mode with delay.
For one button mode press the button 4, for multi
button mode press the button 5 and for multi button
mode with delay press the button 6.
Press the button ON for confirmation of the selected
mode. Changing the setting and transition to the
operation mode is signaled by the green flashing of
LED and
.
Note:
The wrong password has been indicated by the
acoustic signal (2 beeps) and LED and LED
flashing alternately red.
Changing the password
Press the buttons ON, OFF and ESC in the same
time. The LED will be flashing red.
Choose a four-digit password and press the button
ON for confirmation the password. LED
start
permanently illuminated green and state of LED
independent on the actual mode (it can flashing or
iliminated).
Press the button 0, LED start flashing red.
Choose for-digit numerical combination for new
password and press the button ON for confirmation.
LED
start flashing red too.
Choose
again
indentical
4-digit
numerical
combination of the new password and press the
button ON for confirmation. Changing the password
and transition to the operation mode is signaled by
the green flashing of LED and
.
Note:
While choosing different numerical combinations it is
signaled by the accoustic signal (2 beeps) and LED
and LED
flashing alternately red.
The setting mode ends after 10s if it is not pressed
agin during that tiime.(it is signaled by accoustic sig-
nal and by the red fleshing the LED and LED
).
To program the keyboard code to the receiver memo-
ry, it is necessary for the keyboard to send a so-called
initialization code during the time the receiver is in the
programming mode. To send the initialization code,
press the selected button ( combination of buttons)
twice with a pause between the two presses. The
pause cannot be no longer than 2 s.
To ensure the maximum range, do not place the key-
board on a metal base or near metal objects. Under
typical operating conditions, the battery lifetime is mo-
re than 10 years. A weak battery is indicated by a
change in the LED flashing. If the battery is weak,
even and regular, the flashing will change to short
blinking. Indication LEDs in some receivers will indi-
cate a weak battery in the transmitter, as well. If you
need to replace the battery, unscrew the cover and
open it.
RESET TO DEFAULTS
If the password is lost, it is possible revert back to the
factory setting (password 1234, multi button mode).
Disconnect the battery, press and hold the button ON
while connecting the battery. Hold the button until
LED and a
starts illuminating red (after about
10 s). While the LED and
are lit up (approx. 3
s), release the button ON and press it briefly again.
Resetting to the manufacturer's defaults will be indica-
ted by simultaneously green flashing LED a
.
ENIKA.CZ s.r.o. hereby declares that this P8 T Key-
board complies with the essential requirements and
other rele-vant provisions of Directive 1999/5/EC.
Prohlášení o shodě
Výrobce:
ENIKA.CZ s. r. o.
190 00 PRAHA 9, Pod Harfou 933/86
IČO: 28218167
tímto prohlašuje, že výrobek
typové označení:
P8 T Keyboard
specifikace:
---
druh výrobku:
vysílací klávesnice
frekvence:
868,3 MHz
vf výkon:
10 dBm
-
je ve shodě se základními požadavky
NV 426/2000 Sb.
v platném
znění a s
NV 481/2012 Sb.
v
platném znění
-
odpovídá základním požadavkům a dalším ustanovením evropské di-
rektivy
1999/5/ES (R&TTE)
(Směrnice o radiových zařízeních a tele-
komunikačních koncových zařízeních a vzájemném uznávání jejich
shody)
a evropské direktivy
2011/65/EU (RoHS)
-
splňuje požadavky těchto norem a předpisů:
rádiové parametry, EMC:
ČSN ETSI
EN 300 220-1 V2.1.1: 2007
ČSN ETSI
EN 300 220-2 V2.1.1: 2006
ČSN ETSI EN 301 489-1 V1.6.1: 2006
ČSN ETSI EN 301 489-3 V1.4.1: 2003
elektrická bezpečnost:
ČSN EN 60950-1 ed.2: 2006
Toto prohlášení je vydáno na výhradní odpovědnost výrobce.
V
Nové Pace dne 28.02.2013
ing. Vladimír Militký,
řízení sytému jakosti
