England's Stove Works 25-EP Скачать руководство пользователя страница 32

Page | 32 
 

DAILY MAINTENANCE 

Important Notes 

 

As with any maintenance concerning this unit, be sure the unit is “OFF” and 
has completed the Shut-Down cycle 

BEFORE

 beginning. 

 

Be aware that metal parts in the firebox can remain 

HOT

 long after the fire 

has gone out and 

EVEN

 after the Shut-Down cycle is complete.  Always use 

extreme caution when handling potentially hot stove parts, even if you think 
they should be cold. 

 

Ashes should only be removed when the stove has been shut-down and has 
been allowed to cool thoroughly.  Hot embers can remain under ashes long 
after the fire has gone out, so always be extra careful when handling any 
ashes from this (or any) stove. 

 

Store ashes in a metal container with a tight fitting lid, and only place this 
container on a non-combustible surface. 

 

Different pellets will generate varying amounts of ash and burnpot deposits.  
Carefully monitor the ash build up in the stove when first operating the unit, 
as well as whenever a different brand of pellets is burned. 

 

While the amount of ash generated by this unit is not excessive compared to 
a traditional log-burning woodstove, keeping the unit clean and free of ash is 
ESSENTIAL for peak performance and maximum efficiency.  Ash build-up 
hampers airflow, reduces efficiency, and can cause a smoke back. 

 

England’s Stove Works

®

 is not responsible for any damages incurred due to 

a poorly maintained and/or dirty stove.  This pellet stove is a highly efficient 
machine and, as such, requires sufficient maintenance to keep it operating at 
its peak. 

Disposal of Ashes

 – Ashes should be placed in a metal container with a tight 

fitting lid.  The closed container of ashes should be placed on a noncombustible 

floor or on the ground, well away from all combustible materials, pending final 

disposal.  If the ashes are disposed of by burial in soil or otherwise locally 

dispersed, they should be retained in the closed container until all cinders have 

been thoroughly cooled. 

Содержание 25-EP































































Отзывы: