Englander 10-CPM Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 42

background image

IMPORTANT!

READ AND FOLLOW

ALL

INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

6



The Pellet/Corn/Multi-fuel stove is tested for operation with corn with

14% or less

moisture content; it is recommended that corn with

11-12%

moisture be used for most

efficient operation of this unit.

Corn with over 12% moisture has a lower BTU value

and will be hard to burn on the lower settings.



Corn must be clean and free from debris; never burn corn straight from the field. Stalk

parts, excessive fines and cob remnants, etc. will clog the auger mechanism. We highly
recommend the use of a sifter; sifters to filter your corn are available from dealers.
Damage caused by dirty and/or unfiltered (unsifted) corn is not covered by the product
warranty – ask for and use clean filtered bagged corn only.



DISCLAIMER NOTICE:

No guarantee is made regarding the heating capacity of this

product. The actual area that this unit will heat depends on factors such as building
conditions, heat loss, type of construction, amount and type of insulation, type of air
movement and heat distribution, and the location of the product.



Important:

Your home must be checked to verify that there is no negative pressure that

will affect the operation of this appliance.



IMPORTANT: DO NOT BURN “TREATED” SEED CORN IN YOUR STOVE.

Seed corn

is treated with chemical pesticides that are harmful or fatal if swallowed; therefore, seed
corn is dangerous to have in the house, especially where children can reach it. Burning
treated seed corn in your stove will void your warranty and will destroy the exhaust
system on the unit.



There are many varieties of corn grown around the world. Each variety has unique

characteristics including the shape and size of the kernel. Your stove will burn more
consistently with a small to medium kernel corn. If the kernel size of the corn varies
greatly or if you switch sources frequently, you will get a less consistent burn. Do not use
corn with high wax content.



Vacuum the hopper out after every 6-8 bags to eliminate buildup of saw dust and fines

from corn.



Your unit was primarily designed to burn pellets, but will also burn dried cherry pits.

Make sure your supplier is selling Dried Cherry Pits (preferably with less than 4%
moisture content) for use as fuel in pellet burning stoves.



IMPORTANT: DO NOT USE CHERRY PITS DESIGNED FOR CRAFTS AND HOBBIES.

This type is usually bleached and/or over-dried.

«
...
4
5
6
7
8
...
»

Содержание 10-CPM











































Отзывы:

Нет отзывов

Похожие инструкции для 10-CPM

Бренд: RAIS Страницы: 36

Бренд: Valor Страницы: 8

Primarofen PO 03-2 easy.nrg

Бренд: wodtke Страницы: 68

LAKEFIELD-2 2-L

Бренд: kozy heat Страницы: 49

Бренд: Twin-Star International Страницы: 2

Windsor WR270007

Бренд: Vermont Castings Страницы: 24

Бренд: Ravelli Страницы: 12

Бренд: Rommelsbacher Страницы: 16

Бренд: Quadra-Fire Страницы: 40

Бренд: Country Hearth Страницы: 24

Бренд: Country Flame Страницы: 19

Бренд: Country Heart Страницы: 24

Бренд: COUNTRY FLAME TECHNOLOGIES Страницы: 37

Бренд: Cola Страницы: 54

Бренд: Contura Страницы: 20

highlander 7 solo

Бренд: Dunsley Heat Страницы: 4

Hasvik 231.17 ST

Бренд: Haas+Sohn Страницы: 2

Бренд: USSC Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды