Industrial Wide-Gap
Magnetic Contacts
SM-4601-LQ / SM-4601-L3Q
Manual
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Phone: (949) 261-2999 | (800) 662-0800
Email: [email protected]
®
PICNN1
MI_SM-4601-LxQ_220415_ML.docx
Useful for industrial situations where a wide-gap,
surface mount contact is needed
36″ (91cm) Wire leads enclosed in armored cable
Contact switch has iridium-plating for a high
melting point and Vickers hardness for higher
power handling and a longer expected life
Weatherproof (IP65) and sealed for outdoor use
Rugged aluminum housing
3″ (76mm) Gap
Mounting bracket included
Lifetime limited warranty
Parts List
1x
Contact switches
1x
Magnets
2x
Mounting screws
1x
Manual
1x
Mounting bracket
NOTICE:
The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also
not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A., Inc. or their respective owners. Copyright © 2022 SECO-LARM U.S.A., Inc. All rights reserved.
Specifications
Overview
SM-4601-LQ shown
Model
SM-4601-LQ
SM-4601-L3Q
Loop type
Closed loop
Open/closed loop
Electrical configuration
N.O. (SPST)
NO/NC
(Form C
–
SPDT)
Operation gap
3" (76mm)
Connectors
36" (91cm) Leads
Material
Case
Aluminum
Contacts
Iridium plated
Contact rating
1.0A@10VDC (max.)
10W (max.)
Switch cycles
50 Million (0.1mA@5VDC)
IP Rating
IP65 Weatherproof
Operating temperature
-15°~160° F (-25°~70° C)
Dimensions Switch
3″x1″x
1
/
2
″ (76x25x13 mm)
Magnet
3″x1″x
1
/
2
″ (76x25x13 mm)
Magnet type
Rare-earth neodymium
Installation
Please read the manual carefully before you begin the installation.
1.
Mount the contact on the track in a safe location away from equipment interference and near where the
magnet will be when the door is closed.
2.
Run the armored cable out of the way. Run wires from the alarm control panel and connect to the
corresponding wires extending from the cable armor.
3.
Mount the magnet on the roll up door so that it will trigger the contact when the door is closed. Be sure
that the gap between the contact and magnet does not exceed 3" (76mm).
LIMITED LIFETIME WARRANTY:
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for the lifetime of the product. SECO-LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. Under no circumstances will SECO-LARM be responsible for any
costs or charges for removal, installation, or reinstallation. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects
in material and workmanship. The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to repair or replacement only, at SECO-LARM’s option. In no event shall
SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any kind to the purchaser or anyone else. This lifetime limited warranty is for products
sold and installed in the United States and Canada. For all other countries the warranty is 1 (one) year.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information, go to
www.P65Warnings.ca.gov
.
GND
N.O.
Alarm Control
Panel
Contact and magnet must be installed on
the protected side of the door.
Wiring shown is for the SM-4601-LQ.
SM-4601-L3Q will be different.
SM-4601-LQ only
