ENFORCER Two-Channel RF Receiver
2
SECO-LARM U.S.A., Inc.
Each channel relay can be programmed for one of five output functions.
SK-910RB2Q only:
Each channel can be
independently programmed to operate in a different function, depending on the user’s application. The five functions are:
1.
4-Second Timed Output
(default) – When the transmitter button is pressed, the relay will turn ON for 4 seconds.
2.
Toggle Output
– Works much like a toggle switch to turn a device ON & OFF alternately. Press the transmitter button
once, and the relay turns ON. Press the transmitter button again, and the relay turns OFF.
3.
Latch Output
– Press the transmitter button once, and the relay turns ON and stays ON. The channel relay will remain
ON regardless of whether a compatible transmitter button is pressed again or not. To turn the relay OFF, press the
channel’s mode switch on the receiver once to reset.
4.
Validity Output
– The channel will turn the relay ON for as long as the transmitter button is pressed.
Note: Due to possible interference or drops in transmitter battery power while the transmitter button is continuously
pressed (even for short periods of time), the receiver may lose the transmitter’s signal and turn the relay OFF.
5.
1-Second Timed Output
– When the transmitter button is pressed, the relay will turn ON for 1 second.
1. Press the channel mode switch of the desired channel for 3 seconds or more. The channel’s LED will start to flash
quickly to indicate that it is in learning mode.
2. While the LED is flashing, press the button of the transmitter to be learned one time. The receiver’s channel indicator
LED will flash once to indicate the transmitter button has been successfully learned. After the button has been learned,
the receiver will automatically exit learning mode. To learn further codes, repeat step 1 to re-enter learning mode.
NOTES:
The channel mode switch(es) can be found at the rear of the receiver’s case.
The channel’s indicator LED will flash a maximum of 15 seconds. If no transmitter button is pressed during this time, the
receiver will exit code learning mode, and the LED will turn off.
If the code being learned has already been learned, the channel indicator LED will turn steady ON and then start flashing
again. The code will not be learned a second time.
One channel can learn the codes of a maximum of 15 transmitter buttons. If you attempt to learn a sixteenth transmitter
code, the earliest code learned will be deleted and the new code will be learned.
Code Learning a New SK-939TP2AQ Transmitter Button:
Each receiver channel can learn the codes of up to 15 different transmitters on a first-in, first-out basis. Below is the
procedure for code learning a new transmitter button.
Clear Channel Memory:
To clear all codes from a channel’s memory, press the channel’s mode switch for 3 seconds or more until the channel
indicator LED flashes. Release, and then press the switch again for 3 seconds or more until the LED stops flashing. The
LED will then flash twice to indicate that all codes associated with that channel have been deleted.
Display Channel Memory:
To see how many codes have been learned by a channel, press that channel’s mode switch once. The number of codes
stored in the channel’s memory is equal to the number of times the channel indicator LED flashes.
Programming Channel Relay Output Function:
Selecting the relay output function:
Hold down the channel function switch for 3 or more
seconds. The channel’s LED will flash a number of
times equal to the output mode that it is in.
To change a channel’s function, press the channel’s
function switch. Each press moves to the next
function in the sequence as shown in the diagram to
the right.
After changing functions, count the number of times
the channel LED flashes to verify the channel is set
to the correct function.
To exit function programming, hold the appropriate
function switch for 3 seconds, or wait 15 seconds.
Note:
For a diagram of the PC board, including the location
of the function switch(es), please see
Overview
, page 3.
Toggle Output
(2 flashes)
Validity Output
(4 flashes)
4-sec (default)
Timed Output
(1 flash)
Latch Output
(3 flashes)
1-sec Timed Output
(5 flashes)
