®
No Touch Request-To-Exit Sensor
2
SECO-LARM
U.S.A., Inc
Features:
•
Adjustable sensor range up to 7" (18cm).
•
Weather resistant for outdoor use.
•
Stainless steel plate.
•
1A relay, adjustable trigger duration 0.8~30
seconds or toggle.
•
LED illuminated sensor area for easy
identification.
•
Selectable LED colors (turns from red to
green or green to red) to show sensor
activated.
Overview:
Specifications:
Power
12~24 VDC
Current
drain
(max.)
Standby
16mA@12VDC / 25mA@24VDC
Triggered
25mA@12VDC / 32mA@24VDC
Relay type
Form C dry contact, 1A@30VDC
Response time
10ms
LEDs
Standby
Red
2
Triggered
Green
2
Output time
0.8~30 s, toggle
Range
2”~7” (5~18 cm)
IP rating
IP65
3
Temperature range
-4°~131° F (-20°~55° C)
Weight
Single Gang
108g
Single Gang
w/ Mechanical Override
125g
Slimline
61g
Slimline
w/ Mechanical Override
77g
European Plate
77g
2
Color function reversible
3
Front panel only.
1
1
/
2
”
(39mm)
2
3
/
4
”
(70mm)
Sensor range adjustment
Trigger time adjustment
LED control jumper
5-pin connector
Form C Mechanical override
1
4
1
/
2
”
(115mm)
1
SD-9163-KSVQ and SD-9263-KSVQ
only
SD-9263-KSVQ shown
2
3
/
4
”
(70mm)
4
1
/
2
”
(115mm)
86mm
86mm
European Plate
ENFORCER
®
No Touch Request-To-Exit Sensor
SECO-LARM
U.S.A., Inc
3
Wiring Diagram:
Installation:
1.
Run four wires through the wall to a single-gang or slimline back-box.
2.
Connect the four wires from the back-box to the Request-to-Exit
Sensor according the
Wiring Diagram
above.
3.
Screw the plate into the back-box, taking care not to crimp the wires.
4.
Remove clear protective film from the sensor before use.
WARNING:
Do not connect any device that will exceed 1A@30VDC.
Changing the LED Color Jumper Placement:
Slimline Models
Single-Gang Models
Adjusting the sensor range and trigger time:
1.
The sensor range can be adjusted from 2”~7” (5~18 cm).
2.
The trigger time can be adjusted from 0.8 to 30 seconds or toggle
4
.
NOTE:
Do not force the adjustment trimpots to turn. Only minimal
force is needed.
Standby: Green
Trigger: Red
Standby: Red
Trigger: Green
(default)
Place here for:
Standby: Green
Trigger: Red
Place here for:
Standby: Red
Trigger: Green
(default)
Red Wire: +12~24 VDC
Brown Wire: Ground (-)
Blue Wire: COM
Purple Wire: N.O.
Green Wire: N.C.
Red Wire: +12~24 VDC
Brown Wire: Ground (-)
Blue Wire: COM
Purple Wire: N.O.
Green Wire: N.C.
Slimline models
Single gang models
Wiring for No Touch Sensor
(SD-9263-KSQ shown)
Wiring for No Touch Sensor
with Form C Mechanical Override Button
(SD-9263-KSVQ shown)
Sensor range
adjustment
Trigger time
adjustment
4
Set trigger time to maximum
Trigger time: 0.8~30 seconds, toggle
4
Default: 0.8 seconds
4
Toggle: turn all the way clockwise
Sensor range: 2”~7” (5~18 cm)
Default: 7” (18cm)
