ENFORCER
W
IDE
A
NGLE
B
ULLET
C
AMERA
Installation:
1.
Please read this manual carefully and keep it for
future reference.
2.
Use the camera within given temperature and
electrical limits.
3.
Do not mount the camera where it is exposed to
rain or other moisture, or in humid or dusty
places.
4.
Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
5.
Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals.*
6.
Do not open or disassemble the camera.
There are no field-serviceable parts inside.
7.
Do not drop the camera or subject it to strong
vibrations.
Note:
Many video monitors produce strong
electromagnetic fields close to the display
CRT, especially when the monitor is turned on
or during de-Gaussing, which occurs
automatically with many monitors when the
monitor is turned on.
Before Starting:
1.
Run a 12VDC power supply wire and a video
cable with a male BNC connector through the
wall to where the camera is to
be mounted.
2.
Temporarily connect the camera to the power
supply.
Do not cut DC jack or female BNC
connector as warranty will be voided. If
needed, use the included pigtail connector.
3.
Temporarily connect the camera’s female BNC
connector to the video cable’s male
BNC connector.
4.
While watching the monitor, hold the camera
against the wall or ceiling by hand where it is to
be mounted, then turn the camera until it is
certain that this mounting location is correct.
Use a pencil to mark the location of the six
screw holes in the mounting plate.
5.
Disconnect the power supply and video cable.
6.
Mount the mounting plate to the wall or ceiling
using the six included mounting screws. If the
wall is made of dry wall, brick, or similar
material, it may be necessary to use screw
anchors (not included).
7.
Reconnect the power supply and video cable.
Turn the monitor on and make sure the camera
is sending the proper video signal.
8.
Adjust the camera angle using the
adjustment nut.
9.
Do a final test of the video camera and
monitor.
Overview:
Camera
Mounting holes
Adjustment nut
Important:
Do not cut DC jack or female BNC connector as warranty will be voided.
DC jack
Connect to video cable’s
male BNC connector
BNC connector
Pigtail connector
Mounting bracket
ENFORCER
W
IDE
A
NGLE
B
ULLET
C
AMERA
Type
Wide-Angle Bullet Camera
CCD
1
/
3
” Sony Super HAD II Color CCD
Resolution
Color: 550 TV Lines
B/W: 590 TV Lines
Pickup elements
768x494 pixels
Video output format
NTSC
Video output
1.0Vp-p composite video, 75Ω
Lens
2.2mm
Viewing angle
170°
Minimum illumination
0.1-lux at F/1.4
S/N ratio
>48dB
Scanning frequency
15.734KHz x 59.94Hz
Sync
Internal
Gamma correction
0.45
Gain control
Auto
IP rating
IP66
Power source
12VDC
Current draw
83mA
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
3
1
/
2
”x1
7
/
16
”x1
7
/
16
” (90x37x37 mm)
Weight
6-oz (160g)
Specifications
3
1
/
2
” (90mm)
1
9
/
16
” (40mm)
1
9
/
16
”
(40mm)
1
7
/
16
”
(37mm)
Parts List:
Dimensions:
1 x Manual
6 x Mounting screws
5
1
/
2
” (140mm)
1 x Pigtail connector
1 x Camera
1 x Mounting bracket
