ENFORCER Wireless Video Door Phone
12
SECO-LARM U.S.A., Inc.
MiDP-236Q_140612.docx
PICKN1
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
Website: www.seco-larm.com
E-mail: [email protected]
IMPORTANT: Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws
and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this product
in violation of any current laws or statutes.
WARNING: Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT: FCC Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period
of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective
part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,
improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is not operating
properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at SECO-LARM’s
option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property damages of any
kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without notice.
SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2014 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part, without
the written permission of SECO-LARM.
The monitor’s screen is blank.
•
Make sure the “ON/OFF” button was pressed.
•
Recharge the monitor’s battery.
•
Plug the charger directly into the monitor.
The monitor recharges when plugged
directly in, but not in the recharging stand.
•
Check that the monitor is firmly seated in the charging
stand, indicated by the cradle’s red charging light.
The monitor’s screen turns on, but
does not display the camera’s image.
•
Check that the monitor has been paired with the camera.
•
Check that the monitor is within range of the camera.
The monitor’s screen image quality is
poor.
•
Adjust the monitor’s display brightness.
•
Clean the camera’s lens using a soft, clean cloth.
•
Change the position of the camera.
•
Move the monitor away from microwaves, television, lamps,
and other potential sources of electromagnetic interference.
The monitor’s “ON/OFF” button does not
unlock the door’s optional locking device.
•
Check the wiring between the camera and the optional
door locking device.
•
Check that the correct power supply is in use.
•
Check that the unit is in two-way communication.
Troubleshooting:
