EnerSys alpha LPS36, Техническое руководство

Страница: 41 / 86

39 0120011-J0 Rev M
Figure 33 — Locations for Chassis Ground (LPS36 Compact, side view)
6�6�3 Input and Output Wiring (6" shelf)
This power system is suitable for installation as part of a Common Bonding Network (CBN) and is intended to be
used in a DC-I configuration (isolated from frame ground).
This system is intended to be used with a -48Vdc rectifier/ battery system at the input, and surge protectors and line
terminators at the output.
6�6�4 Wiring Chassis Ground
Protective earthing terminals are provided for chassis ground at the left front side of LPS36 Compact. If necessary,
the terminal can be moved to the right side. Undo the two screws securing the terminal plate and move it to the right
side, use the same two screw to secure the terminal plate.
1. Connect the power system chassis to the master ground bus (MGB). This connection is necessary for
personnel safety and to meet many telco-grounding requirements.
2. Use minimum #6 AWG (16mm) copper wire and standard 2-hole crimp lugs for 1/4" studs on 5/8" centers.
3. Secure the lugs with 1/4-20 serrated flanged nuts (supplied) to provide the anti-rotation necessary for primary
ground connections.
4. The screws for securing the ground terminal plate can also be reoriented on the opposite side of the module.
For additional information refer to the Customer Connections drawings at the end of this manual (0300189-08).
SCALE:
REV
SHEET
SIZE DWG NO.
TITLE:
OF
A
1:2
B
1 1
0300189-08
CUSTOMER CONNECTIONS,
LPS 36 COMPACT SHELF
THESE DESIGNS AND SPECIFICATIONS ARE
CONFIDENTIAL, REMAIN THE PROPERTY OF
ALPHA TECHNOLOGIES LTD., AND SHALL NOT BE
COPIED OR USED WITHOUT ITS WRITTEN CONSENT
© ALPHA TECHNOLOGIES LTD
CHECKED
DRAWN
DATE APPROVALS
G. LUMANOG
May-29-15
May-29-15 K.LAU
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
DIM ARE IN MM
INTERPRET DIM AND TOL PER
ASME Y14.5M-1994
X
X.X
X.XX
ANGULAR:
1
1
0.5
0.25
REFER TO NAMEPLATE FOR INPUT/OUTPUT VOLTAGE AND CURRENT RATEINGS. 1.
NOTES UNLESS OTHERWISE SPECIFIED:
REFER TO BUBBLE NUMBER
IN BILL OF MATERIALS.
ITEM
GROUND TERMINAL
1/4" STUD 5/8" CENTER TO CENTER
TORQUE TO 12 NM (105 in-lb)
FOR CONNECTING TO
FAN TRAY (IF USED)
OUTPUT CONNECTOR
50 POSITIONS, CHAMP-LOK
SEE OUTPUT CONNECTIONS TABLE
INPUT CONNECTIONS
1/4" HOLE 5/8" CENTER TO
CENTER LUG, SEE LABEL
ON WIRE FOR POLARITY
ALARM CONNECTION CABLE,
9 CONDUCTORS, AWG#22,
SEE ALARM CONNECTIONS TABLE,
FORM C CONTACTS, MAX CURRENT 1A, 60V
CAN BUS
CONNECTOR
MODULAR JACK
6P6C
SEE CAN BUS TABLE
LPS36 MODULE
MAXIMUM 4 MODULES
SCREWS SECURING THE GROUND
TERMINAL PLATE, UNDO SCREWS TO
MOVE GROUND TERMINAL TO THE
OTHER SIDE.
REVISIONS
LTR DESCRIPTION DWN DATE CHK
A INITIAL RELEASE KLAU May-29-15 GL
OUTPUT CONNECTIONS
PIN# MODULE CHANNEL PIN# MODULE CHANNEL
1
1
CH1_-190V 26
1
CH1_+190V
2 CH2_-190V 27 CH2_+190V
3 CH3_-190V 28 CH3_+190V
4 CH4_-190V 29 CH4_+190V
5
2
CH1_-190V 30
2
CH1_+190V
6 CH2_-190V 31 CH2_+190V
7 CH3_-190V 32 CH3_+190V
8 CH4_-190V 33 CH4_+190V
9
3
CH1_-190V 34
3
CH1_+190V
10 CH2_-190V 35 CH2_+190V
11 CH3_-190V 36 CH3_+190V
12 CH4_-190V 37 CH4_+190V
13
4
CH1_-190V 38
4
CH1_+190V
14 CH2_-190V 39 CH2_+190V
15 CH3_-190V 40 CH3_+190V
16 CH4_-190V 41 CH4_+190V
17 N/C 42 N/C
18 N/C 43 N/C
19 N/C 44 N/C
20 N/C 45 N/C
21 N/C 46 N/C
22 N/C 47 N/C
23 N/C 48 N/C
24 N/C 49 N/C
25 N/C 50 N/C
ALARM CABLE CONNECTIONS
WIRE COLOUR ALARM SIGNAL
BROWN FAN ALM NC
WHITE FAN ALM COM
BLUE FAN ALM NO
BLACK MAJOR ALM NC
ORANGE MAJOR ALM COM
RED MAJOR ALM NO
VIOLET MINOR ALM NC
GREEN MINOR ALM COM
YELLOW MINOR ALM NO
CAN BUS
PIN # SIGNAL
1 GND
2 CAN H
3 N/C
4 CAN L
5 N/C
6 N/C
A
B
C
D
E
1 2 3 4
5
D
A
C
E
B
1 3 5 4 2
DO NOT SCALE DRAWING
Recommended torque values
1/4-20 105 in-lb [12 N-m]