Energy Tech Laboratories Modular Direct Fired Heaters Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 28

background image

A0011030

December 2011 Rev. 17

FOR YOUR SAFETY

The use and storage of gasoline or other flammable vapors and liquids in open containers in the
vicinity of this appliance is hazardous.

Standard and Modular Direct Fired Heaters

Installation, Operation, and Maintenance Manual

Modular Direct Fired Heater

Standard Direct Fired Heater

Direct Fired Module

Save these instructions.  This document is the property of the owner of this equipment and is
required  for  future  maintenance.    Leave  this  document  with  the  owner  when  installation  or
service is complete.

RECEIVING AND INSPECTION

Upon  receiving  unit,  check  for  any  interior  and  exterior  damage,  and  if  found,  report  it
immediately  to  the  carrier.    Also  check  that  all  accessory  items  are  accounted  for  and  are
damage  free.    Turn  the  blower wheel  by  hand  to  verify  free  rotation  and  check  the  damper  (if
supplied) for free operation.

WARNING!!

Improper  installation,  adjustment,  alteration,  service  or  maintenance  can  cause  property
damage,  injury  or  death.    Read  the  installation,  operating  and  maintenance  instructions
thoroughly before installing or servicing this equipment.  ALWAYS disconnect power and gas
prior to working on heater.

FOR YOUR SAFETY

If you smell gas:
1.

Open windows.

2.

Don’t touch electrical switches.

3.

Extinguish any open flames.

4.

Immediately call your gas supplier.

1
2
3
...
»

Содержание Modular Direct Fired Heaters





























Отзывы:

Нет отзывов

Похожие инструкции для Modular Direct Fired Heaters

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

VRV EMERION RXYQ-AATJA

Бренд: Daikin Страницы: 429

Бренд: A.O. Smith Страницы: 4

Бренд: Rinnai Страницы: 20

FXV-1212C-32Q-M/Q

Бренд: BAC Страницы: 47

Бренд: ACC Страницы: 192

Бренд: Cadet Страницы: 8

Бренд: Zodiac Страницы: 32

HydroTap All-In-One BC 60/85A

Бренд: Zip Страницы: 24

Бренд: Frico Страницы: 6

Бренд: Rheem Страницы: 47

Бренд: Toyostove Страницы: 18

MAESTRO SMART 9HP

Бренд: Olimpia splendid Страницы: 52

Бренд: A.O. Smith Страницы: 74

Бренд: Zibro Страницы: 14

Бренд: i4Home Страницы: 2

AFFINITY YZH02411

Бренд: York Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды