THE PINNACLE CEILING FAN
INSTALLATION INSTRUCTIONS
Please read and save these instructions
These instructions are to be used in
the installation of the following
QUORUM INTERNATIONAL fans...
The Pinnacle
(WET LISTED)
P.O. Box 961008 • Fort Worth, TX 76161 • (817) 626-5483 • FAX (817) 626-5540
I0108-7/06
© 2006 Quorum International. All Rights Reserved.
7. FAN OPERATION AND CARE
8. TROUBLESHOOTING
6. COMPLETING
THE
INSTALLATION
1.
Make sure the wiring is safely inside
the outlet box as instructed in Step 5 -
Electrical Connections. To install the
canopy, partially unscrew the 2 screws in
the hanger bracket. Align the slotted
holes in the canopy with the screws in
hanger bracket. Push up the canopy so
the screws slip into the slot. Turn the
canopy so it locks in place. Make sure the
canopy is not quite touching the ceiling.
2.
Blade Assembly & Installation
(Fig. 10) Using the supplied blade arm
screws, attach the blades to the blade
arms. In some cases the metal washer is
permanently fixed to the screw head.
Ensure all screws are used for each
blade. Next attach the blades to the
motor assembly using the supplied
screws.
DO NOT bend the blade arms
when installing the blades.
3.
Attaching the Control Cup
(Fig. 11) Attach the control cup plate to
the flange of the motor by using the three
(3) screws provided that are pre-installed
on the flange. (Fig. 12) Join the two ends
of the square cannon plugs (lining up the
colors) and attach the control cup to the
control cup plate with the three (3)
screws provided.
A certain amount of wobble may be
considered normal, especially if the fan
is on a downrod longer than 12".
4.
Turn on the fan and check the 4
position speed switch - 3 speeds and
stop. (Fig. 13) Check the reverse switch
NOTE: Wait for the fan to stop rotating
before changing from forward to reverse.
Fig. 12
Flange
w/ control
cup plate
Control Cup
Fig. 10
Blade
Blade Arm
1.
A ceiling fan is an environmentally
smart choice to cool as well as help to
warm your home or office. You should
see a reduction in both heating and cool-
ing costs by regular use of your fan.
Do not hesitate to use your fan dur-
ing summer and winter months. In sum-
mer, using the reverse switch, adjust the
fan’s direction so cool air is blown down,
producing a cooling breeze. (Fig, 14) In
winter, reverse the fan so that an upward
airflow will push warm air off the ceiling
and circulate it downwards into the liv-
ing area (Fig. 15). In winter months, use
the fan at a lower speed than summer.
2.
Periodically check tightness of all
screws securing the blades to the blade
arm attachment points. A clicking or
rattling noise is a sure indication of
loosening screws. Since screws will
invariably work loose over time, at least
once a year, tighten all the screws attach-
ing blades to blade arms.
Do not bend
blade arms when cleaning or servicing
the fan.
3.
Clean your fan periodically using
only a cloth dampened with a mild deter-
gent solution for all hardware - never use
solvents. The finish plating is lacquered
to prevent tarnishing. Use a lint-free cloth
with clean water to clean blades.
4.
You will never need to oil or lubri-
cate your fan. Its permanently sealed
bearings will provide trouble-free, silent
operation for many years.
5.
If repairs or servicing are ever
required, to avoid possible electric
shock,
turn off the electricity
at the
main fuse or circuit panel before you
begin.
FAN WILL NOT START
1.
Check that the electricity has been
turned on at the circuit breaker which
had probably been turned off during
installation.
2.
Turn off the electricity. Check all
connections in the wiring of the fan at the
ceiling and make sure it follows the wiring
instructions outlined in this manual.
NOISE
Note:
Always allow a day or two “run-in”
time for any new fan at medium or high
speed. When attempting to diagnose
noise, listen carefully from several sides
to try and isolate the location of the noise
(blades, upper end, motor, light kit, etc.).
1.
Tighten all screws attaching blades to
blade arms. Remember to tighten these
screws at least once a year because they
may loosen slowly over time and cause a
clicking noise.
2.
Turn off the power. Loosen the
canopy and check that the wiring and/or
wire nut connectors are not resting against
the canopy, possibly vibrating while the
fan is on.
3.
Use of a standard light rheostat or an
unapproved fan wall control to control the
fan speed will always cause an annoying
“hum”. Many fan motors do not work
quietly with solid state variable speed
controls.
4.
Check that the rubber gasket on the
mounting bracket has been installed if
called for in the installation instructions.
5.
Check that the canopy is not touching
the ceiling.
6.
Check that all screws on the motor
housing and the bottom housing are tight.
FAN TURNS, BUT DOES NOT
MOVE MUCH AIR
1.
The fan may be running in reverse.
2.
The distance from the ceiling to the
blades may be too small. At least 8" are
recommended.
3.
The room may contain items which
obstruct the air flow.
4.
The fan may be too small for the size
of the room.
EXCESSIVE WOBBLE
Note: A small amount of wobble is
considered acceptable and should not be
considered a defect.
1.
Make certain all blades are tightly
attached to each blades' respective blade
arm.
REPLACEMENT PARTS AVAILABLE
A full range of genuine replacement spare parts are available at reasonable cost directly from
Quorum International. Please call us at (817)626-5483, Monday through Friday from 8:00 A.M.
to 5:00 P.M. CST.
Fig. 13
Fig. 11
Reverse Switch
Cannon
Plug
Control Cup
Plate
Flange
Fan
Fig. 13
WINTER
Fig. 14
Version #191525-XX is
Energy Star certified.
