Energetiq LDLS EQ-9-HP Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 37

Energetiq LDLS EQ-9-HP Скачать руководство пользователя страница 24

20

EQ-9-HP Operation Manual

DOC-8240 Rev. 3

Signal Connections

The EQ-9-HP is controlled through the remote I/O connector.

gives the pin assignments and functions for this interface. Connect to the user’s

control system using a suitable cable. Mating connector is a standard high-density 15-pin d-

sub male (for example, Amp part no. 748364-1 with contacts 1658670-2).

Optionally, connect a model EQ-99-RC remote control module to the I/O connector using

the supplied cable

User I/O can be powered either by the EQ-9-HP internal isolated power supply, or an

external supply.

Figure 8 shows connection schematics for both configurations.

Description

Pin #

Details

Commands (Inputs)

LAMP OPERATE

12

OPERATE REQUEST, apply +5V (referenced to digital
common) to initiate start cycle

EXTERNAL INTERLOCK

13

EXTERNAL INTERLOCK, apply +5V (referenced to
digital common) to close interlock and allow operation

Status Indicators (Outputs)

LAMP ON

1

Pulled to digital common when ON

LASER ON

2

Pulled to digital common when ON

LAMP MODULE FAULT

3

Pulled to digital common when OK, float on FAULT

CONTROLLER FAULT

4

Pulled to digital common when OK, float on FAULT

IS5V SUPPLY

5

50mA maximum, referenced to digital common

DIGITAL COMMON

6,7,8,9

Galvanically isolated from system

RESERVED

10, 11

Do not connect

RESERVED

14,15

Do not connect

Table 3

: I/O Connector Pin Assignment

«
...
22
23
24
25
26
...
»

Содержание LDLS EQ-9-HP






































Отзывы:

Нет отзывов