Endress+Hauser Smart System SSP200B Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 36

background image

Electrical connection

Smart System for Aquacultures SSP200B

22

Hauser

6.5.2

Mounting the LTE antenna

The LTE antenna is connected to the Modbus Edge Device upon delivery.

Before mounting the antenna head, we recommend testing the antenna reception at

the mounting location. The antenna head is difficult to disassemble once mounted.

Mounting the LTE antenna

1. Select a suitable mounting location for the antenna head.
2. Disconnect the antenna connection cables on the LTE modem in the Modbus Edge

Device.

3. Pull the antenna connection cables through the cable glands on the Modbus Edge

Device.

4. To secure the antenna head, drill an 11 mm bore in the mounting surface.
5. Guide the antenna connection cables through the bore.
6. Remove the protective film from the antenna head.
7. Stick the antenna head to the mounting surface.
8. Tighten the nut.
9. Guide the antenna connection cables through cable glands C and D.

10. Connect the antenna connection cables to the LTE modem in the Modbus Edge

Device.

2

5

3

1

4

15.0

0.5

±

14.6

0.5

±

12M

15.0

0.5

±

Æ

±

81.3

1

A0042905

 19

LTE antenna

1

Antenna head

2

Protective film

3

Nut

4

Antenna connection cable: LTE-MAIN-SMA male

5

Antenna connection cable: LTE-AUX-SMA male

«
...
20
21
22
23
24
...
»

Содержание Smart System SSP200B





































Отзывы:

Нет отзывов

Похожие инструкции для Smart System SSP200B

Бренд: Saito Страницы: 90

Бренд: Vancare Страницы: 31

Бренд: ZETRON Страницы: 3

Бренд: Yardney Страницы: 8

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Harmar Mobility Страницы: 16

Бренд: Jandy Страницы: 28

Бренд: Jands Страницы: 6

Бренд: Paradox Страницы: 2

Бренд: Saab Страницы: 4

Бренд: U.S. Divers Страницы: 22

Бренд: Vacon Страницы: 50

Бренд: V2 Страницы: 116

Бренд: V2 Страницы: 8

Бренд: V2 Страницы: 25

Бренд: V2 Страницы: 124

Бренд: Watts Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды