Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 130

background image

3 Transducer Block

Device functions Proline Promag 55 FOUNDATION Fieldbus

98

Hauser

Main Line -
Format

AUTO - OOS

Use this parameter to define the maximum number of places after the
decimal point displayed for the reading in the main line.

Options:

XXXXX. - XXXX.X - XXX.XX - XX.XXX -X.XXXX

Factory setting:

X.XXXX

!

Note!

• Note that this setting only affects the reading as it appears on the

display, it has no influence on the accuracy of the system's calculations.

• The places after the decimal point as computed by the measuring device

cannot always be displayed, depending on this setting and the
engineering unit. In these instances an arrow appears on the display
between the measured value and the engineering unit (e.g.
1.2

→

kg/h), indicating that the measuring system is computing with

more decimal places than can be shown on the display.

Main Line Mux -
Assign

AUTO - OOS

Use this parameter to define the second reading to be displayed in the
main line alternately (every 10 seconds) with the value defined in the
parameter "Main Line - Assign".

Options:

OFF
VOLUME FLOW
MASS FLOW
VOLUME FLOW IN %
MASS FLOW IN %
TOTALIZER (1 to 3)
AI1 - OUT VALUE
AI2 - OUT VALUE
AI3 - OUT VALUE
AI4 - OUT VALUE
AI5 - OUT VALUE
PID - IN VALUE (controlled variable)
PID - CAS IN VALUE (external set point)
PID - OUT VALUE (manipulated variable)

Factory setting:

OFF

Main Line Mux -
100% - Value

AUTO - OOS

!

Note!

The entry is not active unless one of the following was selected in the
parameter "Main Line Mux - Assign":
• MASS FLOW IN %
• VOLUME FLOW IN %

Use this parameter to define the flow value to be shown on the display as
the 100% value.

User input:

5-digit floating-point number

Factory setting:

Nominal diameter and country dependent

!

Note!

The unit is taken from the "System Unit - Volume Flow" or "System Unit -
Mass Flow" parameter (

"Display" Transducer Block/base index 1800:

Parameter

Write access with

operating mode

(MODE_BLK)

Description

«
...
96
97
98
99
100
...
»

Содержание Proline Promag 55



































































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Promag 55

Бренд: AAT Страницы: 6

Бренд: Lamtec Страницы: 18

Бренд: Ladybug Страницы: 33

Бренд: YUNEEC Страницы: 6

Бренд: Fabbri Страницы: 4

Бренд: NeuLog Страницы: 4

Бренд: Yoshimura Страницы: 7

COPENHAGEN WHEEL

Бренд: Superpedestrian Страницы: 52

Бренд: SR Suntour Страницы: 10

Бренд: hepco & becker Страницы: 5

Sentrol 60 series

Бренд: ITI Страницы: 3

Бренд: Westfalia Страницы: 71

Бренд: DYNATEK Страницы: 4

Бренд: Gira Страницы: 4

Бренд: hepco & becker Страницы: 5

ANOMULTI ROUND WITH CABLE CLIP AND CABLE AND SAUCER

Бренд: ROSE DISPLAYS Страницы: 4

Бренд: Rohde & Schwarz Страницы: 123

Бренд: Yekbee Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды