Endress+Hauser Proline Promag 55 Скачать руководство пользователя страница 15

Страница: 15 / 130

Device Functions Proline Promag 55 FOUNDATION Fieldbus

4 Block QUICK SETUP

Hauser

Block QUICK SETUP

Block

Group

Function

groups

Functions

QUICK SETUP

(B)

⇒

QS COMMISS.

(1002) P. 15

⇒

T-DAT SAVE/LOAD

(1009) P. 15

Function description

QUICK SETUP

QUICK SETUP
COMMISSIONING
(1002)

Use this function to start the Setup menu for commissioning.

Options:

YES
NO

Factory setting:

Note!

You will find a flowchart of the COMMISSIONING Setup menu on Page 16.
For more detailed information on Setup menus, please refer to the Operating Instructions
for Proline Promag 55 FOUNDATION FIELDBUS.

T-DAT SAVE/LOAD
(1009)

Use this function to save the parameter settings / configuration of the

transmitter

in a

transmitter DAT (T-DAT), or to load the parameter settings from the T-DAT into the
EEPROM (

manual

security function).

Application examples:
• After commissioning, the actual measuring point parameters can be saved to the

T-DAT as a backup.

• If the transmitter is replaced for some reason, the data from the T-DAT can be loaded

into the new transmitter (EEPROM).

Options:

CANCEL
SAVE (from EEPROM to T-DAT)
LOAD (from the T-DAT into EEPROM)

Factory setting:

CANCEL

Note!

• If the target device has an older software version, the message "TRANSM. SW-DAT" is

displayed during startup. Then only the SAVE option is available.

• LOAD

This option is only possible if:
– The target device has the same software version as, or a more recent software

version than, the source device or

– The T-DAT contains valid data that can be retrieved

• SAVE

This option is always available.

Содержание Proline Promag 55



































































































































Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 55, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 55

Отзывы:

Похожие инструкции для Proline Promag 55

Бренды по названию

Популярные бренды