Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 89

Страница: 89 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

Install. direct.



Navigation

 Expert → Sensor → Sensor adjustm. → Install. direct. (1809)

Description

Use this function to change the sign of the medium flow direction.

Selection

• In arrow direct.

• Against arrow

Factory setting

In arrow direct.

Additional information

Description

Before changing the sign: ascertain the actual direction of fluid flow with reference to

the direction indicated by the arrow on the sensor nameplate.

Integration time



Navigation

 Expert → Sensor → Sensor adjustm. → Integration time (6533)

Description

Display the duration of an integration cycle.

User interface

1 to 65 ms

Measuring period



Navigation

 Expert → Sensor → Sensor adjustm. → Measuring period (6536)

Description

Display the time of a full measuring period.

User interface

0 to 1

000 ms

"Variable adjust" submenu

Navigation

 Expert → Sensor → Sensor adjustm. → Variable adjust

‣

Variable adjust

Vol. flow offset (1831)

→  90

Vol. flow factor (1832)

→  90

Mass flow offset (1841)

→  91

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Бренды по названию

Популярные бренды