Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 84

Страница: 84 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

Hauser

Ref. density (1892)

→  86

Temp. source (6712)

→  84

External temp. (6673)

→  84

Ref. temperature (1816)

→  86

Temp. source



Navigation

 Expert → Sensor → External comp. → Temp. source (6712)

Description

Use this function to select the temperature source.

Selection

• Off

• Int.temp. sensor

• External value

• Current input 1

• Current input 2

• Current input 3

Factory setting

Off

External temp.

Navigation

 Expert → Sensor → External comp. → External temp. (6673)

Prerequisite

The

External value

option is selected in the

Temp. source

parameter (→  84).

Description

Use this function to enter the temperature read in from the external device.

User entry

Floating point number with sign

Factory setting

–273.15 °C

Additional information

Dependency

The unit is taken from the

Temperature unit

parameter (→  58)

Visibility depends on order options or device settings

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды