Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 53

Страница: 53 / 272

Proline Promag 300 Modbus RS485

Description of device parameters

Hauser

A0028726

Non-conductive

Conductive

NC NC contact (normally closed)
NO NO contact (normally open)

The output behavior can be reversed via the

Invert outp.sig.

parameter (→  138) i.e.

the transistor does not conduct for the duration of the pulse.
In addition, the behavior of the output in the event of a device alarm (

Failure mode

parameter (→  124)) can be configured.

Switch status 1 to n

Navigation

 Expert → Sensor → Measured val. → Output values → PFS output 1 to n → Switch

status 1 to n (0461–1 to n)

Prerequisite

The

Switch

option is selected in the

Operating mode

parameter (→  120).

Description

Displays the current switch status of the status output.

User interface

• Open

• Closed

Additional information

User interface

• Open

The switch output is not conductive.

• Closed

The switch output is conductive.

"Relay output 1 to n" submenu

Navigation

 Expert → Sensor → Measured val. → Output values → Relay

output 1 to n

‣

Relay output 1 to n

Switch status (0801–1 to n)

→  54

Switch cycles (0815–1 to n)

→  54

Max. cycles no. (0817–1 to n)

→  54

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды