Endress+Hauser Proline Promag 300 Скачать руководство пользователя страница 154

Страница: 154 / 272

Description of device parameters

Proline Promag 300 Modbus RS485

154

Hauser

Factory setting

NaN value

Additional information

Options

• NaN value

The device outputs the NaN value

• Last valid value

The device outputs the last valid measured value before the fault occurred.

This effect of this parameter depends on the option selected in the

Assign diag. beh

parameter.

Bus termination

Navigation

 Expert → Communication → Modbus config. → Bus termination (7155)

Description

Displays whether the terminating resistor is enabled or disabled.

User interface

• Off

• On

Factory setting

Off

Additional information

Selection

• Off

The terminating resistor is disabled.

• On

The terminating resistor is enabled.

For detailed information about enabling the terminating resistor, see the Operating

Instructions for the device, "Enabling the terminating resistor" section

Fieldb.writ.acc.

Navigation

 Expert → Communication → Modbus config. → Fieldb.writ.acc. (7156)

Description

Use this function to restrict access to the measuring device via fieldbus (Modbus protocol).

Selection

• Read + write

• Read only

Factory setting

Read + write

Not a Number

Содержание Proline Promag 300

















































































































































































































































































Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 300, Описание параметров устройства

Результаты поиска

Содержание Proline Promag 300

Отзывы:

Похожие инструкции для Proline Promag 300

Бренды по названию

Популярные бренды