Endress+Hauser Proline Promag 10 Скачать руководство пользователя страница 94

Страница: 94 / 124

11 Description of Device Functions

PROline Promag 10

Hauser

11.3 Group

OPERATION

Function description OPERATION

LANGUAGE

Use this function to select the language for all texts, parameters and
messages shown on the local display.

Options:

ENGLISH
DEUTSCH
FRANCAIS
ESPANOL
ITALIANO

Factory setting:

Depends on country, see factory setting Page 116 ff.

Note!

If you press the

keys simultaneously at startup, the language defaults to

"ENGLISH".

ACCESS CODE

All data of the measuring system are protected against inadvertent change.
Programming is disabled and the settings cannot be changed until a code is
entered in this function. If you press the

keys in any function, the measuring

system automatically goes to this function and the prompt to enter the code
appears on the display (when programming is disabled).

You can enable programming by entering your private code (

factory

setting = 10

, see DEF. PRIVATE CODE function on Page 94)

User input:

Max. 4-digit number: 0...9999

Note!

• The programming levels are disabled if you do not press a key within 60

seconds following automatic return to the HOME position.

• You can also disable programming in this function by entering any number

(other than the defined private code).

• The Hauser service organisation can be of assistance if you

mislay your personal code.

DEF. PRIVATE CODE

Use this function to enter a personal code for enabling programming.

User input:

0...9999 (max. 4-digit number)

Factory setting:

Note!

• Programming is always enabled with the code “0”.
• Programming has to be enabled before this code can be changed. When

programming is disabled this function is not available, thus preventing
others from accessing your personal code.

• The function is not available unless the personal code was entered in the

function ACCESS CODE.

Содержание Proline Promag 10





























































































































Результаты поиска

Содержание Proline Promag 10

Отзывы:

Похожие инструкции для Proline Promag 10

Бренды по названию

Популярные бренды

Endress+Hauser Proline Promag 10, Руководство по эксплуатации

Результаты поиска

Содержание Proline Promag 10

Отзывы:

Похожие инструкции для Proline Promag 10

Бренды по названию

Популярные бренды