background image

Calibration and adjustment

Oxymax COS61D

22

Hauser

6. Is the measured value display on the transmitter stable:

Perform the calibration in accordance with the Operating Instructions for the

transmitter. Pay particular attention to the software settings for the stability criteria

for calibration and for the ambient pressure.

7. Where necessary:

Adjust the sensor by accepting the calibration data.

8. Then place the sensor back into the medium.
9. Deactivate the hold status at the transmitter.

Follow the calibration instructions in the Operating Instructions for the transmitter

used.

7.4  

Calculation example for the calibration value

As a check, you can calculate the expected calibration value (transmitter display) as shown

in the following example (salinity is 0).

1. Determine the following:

• Ambient temperature for the sensor (air temperature in the case of the 

Air 100% rh

 or

Air variable

 calibration methods, water temperature in the case of the 

H2O air-

saturated

 calibration method)

• The altitude above sea level

• The current air pressure (= relative air pressure based on sea level) at the time of

calibration. (If indeterminable, use 1013 hPa.)

2. Determine the following:

• The saturation value S acc. to Table 1

• The altitude factor K acc. to Table 2

Table 1

T

[˚C (˚F)]

S

[mg/l=ppm]

T

[˚C (˚F)]

S

[mg/l=ppm]

T

[˚C (˚F)]

S

[mg/l=ppm]

T

[˚C (˚F)]

S

[mg/l=ppm]

0 (32)

14.64

11 (52)

10.99

21 (70)

8.90

31 (88)

7.42

1 (34)

14.23

12 (54)

10.75

22 (72)

8.73

32 (90)

7.30

2 (36)

13.83

13 (55)

10.51

23 (73)

8.57

33 (91)

7.18

3 (37)

13.45

14 (57)

10.28

24 (75)

8.41

34 (93)

7.06

4 (39)

13.09

15 (59)

10.06

25 (77)

8.25

35 (95)

6.94

5 (41)

12.75

16 (61)

9.85

26 (79)

8.11

36 (97)

6.83

6 (43)

12.42

17 (63)

9.64

27 (81)

7.96

37 (99)

6.72

7 (45)

12.11

18 (64)

9.45

28 (82)

7.82

38 (100)

6.61

8 (46)

11.81

19 (66)

9.26

29 (84)

7.69

39 (102)

6.51

9 (48)

11.53

20 (68)

9.08

30 (86)

7.55

40 (104)

6.41

10 (50)

11.25

Table 2

Altitude

[m (ft)]

K

Altitude

[m (ft)]

K

Altitude

[m (ft)]

K

Altitude

[m (ft)]

K

0 (0)

1.000

550 (1800)

0.938

1050 (3450) 0.885

1550 (5090) 0.834

50 (160)

0.994

600 (1980)

0.932

1100 (3610) 0.879

1600 (5250) 0.830

Содержание Oxymax COS61D













































Отзывы: