Endress+Hauser MODBUS RS485 Скачать руководство пользователя страница 66

Страница: 66 / 92

Diagnostics and troubleshooting

LPGmass Modbus RS485

Hauser

In addition to the operation time of its occurrence and possible troubleshooting measures,

each event is also assigned a symbol that indicates whether the event has occurred or has

ended:

• Diagnostic event

– : Occurrence of the event

– : End of the event

• Information event

: Occurrence of the event

To call up the measures to rectify a diagnostic event:

• Via "FieldCare" operating tool →  61

• Via "DeviceCare" operating tool →  61
For filtering the displayed event messages →  66

12.9.2 Filtering the event logbook

Using the

Filter options

parameter you can define which category of event message is

displayed in the

Events list

submenu.

Navigation path

Diagnostics → Event logbook → Filter options

Filter categories

• All

• Failure (F)

• Function check (C)

• Out of specification (S)

• Maintenance required (M)

• Information (I)

12.9.3 Overview of information events

Unlike a diagnostic event, an information event is displayed in the event logbook only and

not in the diagnostic list.

Info number

Info name

I1000

--------(Device ok)

I1089

Power on

I1090

Configuration reset

I1091

Configuration changed

I1110

Write protection switch changed

I1111

Density adjust failure

I1151

History reset

I1209

Density adjustment ok

I1221

Zero point adjust failure

I1222

Zero point adjustment ok

I1444

Device verification passed

I1445

Device verification failed

I1446

Device verification active

I1447

Record application reference data

I1448

Application reference data recorded

I1449

Recording application ref. data failed

I1450

Monitoring off

Содержание MODBUS RS485





























































































Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser MODBUS RS485, Руководство по эксплуатации

Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды