Endress+Hauser MODBUS RS485 Скачать руководство пользователя страница 52

Страница: 52 / 92

Commissioning

LPGmass Modbus RS485

Hauser

Navigation

"Diagnostics" menu → Simulation

‣

Simulation

Assign simulation process variable

→  52

Value process variable

→  52

Simulation device alarm

→  52

Parameter overview with brief description

Parameter

Prerequisite

Description

Selection / User

entry

Factory setting

Assign simulation process variable

–

Select a process variable for
the simulation process that is
activated.

• Off
• Mass flow
• Volume flow
• Corrected volume

flow

• Density
• Reference density
• Temperature

Off

Value process variable

One of the following options is
selected in the

Assign

simulation process variable

parameter (→  52):
• Mass flow
• Volume flow
• Corrected volume flow
• Density
• Reference density
• Temperature

Enter the simulation value for
the selected process variable.

Depends on the
process variable
selected

Simulation device alarm

–

Switch the device alarm on and
off.

• Off
• On

Off

10.7 Protecting settings from unauthorized access

The following options exist for protecting the configuration of the measuring device from

unintentional modification after commissioning:

Write protection via write protection switch →  52

10.7.1 Write protection via write protection switch

The write protection switch makes it possible to block write access to the entire operating

menu with the exception of the following parameters:

• External pressure

• External temperature

• Reference density

• All parameters for configuring the totalizer
The parameter values are now read only and cannot be edited any more:

• Via service interface (CDI)

• Via Modbus RS485

1. Depending on the housing version, loosen the securing clamp or fixing screw of the

housing cover.

Содержание MODBUS RS485





























































































Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды

Endress+Hauser MODBUS RS485, Руководство по эксплуатации

Результаты поиска

Содержание MODBUS RS485

Отзывы:

Похожие инструкции для MODBUS RS485

Бренды по названию

Популярные бренды