Endress+Hauser Micropilot M FMR245 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 118

background image

Micropilot M FMR245 with PROFIBUS PA

Trouble-shooting

Hauser

91

9.5

Orientation of the Micropilot

For orientation a marker is found on the flange or threaded boss of the Micropilot. During
installation this must be oriented as follows (see Page 10):
• In tanks: to the vessel wall
• In stilling wells: to the slots
• In bypass pipes: vertical to the tank connectors

After commissioning the Micropilot, the echo quality indicates whether a sufficiently large
measuring signal is obtained. If necessary, the quality can be optimised later. Vice versa, the
presence of an interference echo can be used to minimise this by optimum orientation. The
advantage of this is that the subsequent tank mapping uses a somewhat lower level that causes an
increase in the strength of the measuring signal.
Proceed as follows:

#

Warning!
Subsequent alignment can lead to personal injury. Before you unscrew or loosen the process
connection, make sure that the vessel is not under pressure and does not contain any injurious
substances.

1.

It is best to empty the container so that the bottom is just covered. However, alignment can be
carried out even if the vessel is empty.

2.

Optimisation is best carried out with the aid of the envelope graph in the display or the
ToF Tool.

3.

Unscrew the flange or loosen the threaded boss by a half a turn.

4.

Turn the flange by one hole or screw the threaded boss by one eighth of a turn. Note the echo
quality.

5.

Continue to turn until 360° is reached.

6.

Optimum alignment:

L00-FMRxxxxx-19-00-00-en-002

Fig. 4:

Vessel partly full, no interference echo obtained

L00-FMRxxxxx-19-00-00-en-003

Fig. 5:

Vessel partly full, interference echo obtained:

«
...
89
90
91
92
93
...
»

Содержание Micropilot M FMR245























































































































Отзывы:

Нет отзывов

Похожие инструкции для Micropilot M FMR245

Бренд: rainforest Страницы: 2

NUFLO Scanner 2000 microEFM

Бренд: Cameron Страницы: 8

Бренд: Danfoss Страницы: 6

Бренд: Lumel Страницы: 32

Бренд: Han Seung Страницы: 2

Prestige Series

Бренд: Ibanez Страницы: 54

Бренд: Artesia Страницы: 36

Бренд: DAKOTA ULTRASONICS Страницы: 38

Бренд: Schneeberger Страницы: 35

Бренд: DeltaOHM Страницы: 26

Бренд: Teledyne Lecroy Страницы: 4

Бренд: Ratek Страницы: 25

Vigilant Plant MR20000

Бренд: YOKOGAWA Страницы: 230

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 47

Бренд: Erma Electronic Страницы: 24

Бренд: Samick Страницы: 48

Бренд: TE Connectivity Страницы: 5

BIP LD2-T017-01-EP-S4 Series

Бренд: Balluff Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды