Endress+Hauser Micropilot FMR56 Скачать руководство пользователя страница 82

Страница: 82 / 198

Commissioning (block-based operation)

Micropilot FMR56, FMR57 FOUNDATION Fieldbus

Hauser

12.2.4 Configuring the Analog Input Blocks

The device has 2 permanently instanced Analog Input Blocks that can be assigned as

required to the various process variables. If required, up to 5 Analog Input Blocks can be

instanced through the FOUNDATION Fieldbus configuration tool.

Default settings

Analog Input Block

CHANNEL

AI 1

32949: Level linearized

AI 2

32856: Distance

1. If necessary, change the block name.
2. Set the block mode to

OOS

by means of the

Block Mode/MODE_BLK

parameter,

TARGET

element.

3. Use the

Channel/CHANNEL

parameter to select the process variable which should

be used as the input value for the Analog Input Block.

4. Use the

Transducer Scale/XD_SCALE

parameter to select the desired unit and the

block input range for the process variable →  82. Make sure that the unit

selected suits the process variable selected. If the process variable does not suit the

unit, the

Block Error/BLOCK_ERR

parameter reports

Block Configuration Error

and the block mode cannot be set to

Auto

5. Use the

Linearization Type/L_TYPE

parameter to select the type of linearization for

the input variable (factory setting:

Direct

). Make sure that the settings for the

Transducer Scale/XD_SCALE

and

Output Scale/ OUT_SCALE

parameters are the

same for the

Direct

linearization type. If the values and units do not match, the

Block

Error/BLOCK_ERR

parameter reports

Block Configuration Error

and the block

mode cannot be set to

Auto

6. Enter the alarm and critical alarm messages by means of the

High High Limit/

HI_HI_LIM

High Limit/HI_LIM

Low Low Limit/LO_LO_LIM

and

Low Limit/

LO_LIM

parameters. The limit values entered must be within the value range

specified for the

Output Scale/ OUT_SCALE

parameter →  82.

7. Specify the alarm priorities by means of the

High High Priority/HI_HI_PRI

High

Priority/ HI_PRI

Low Low Priority/LO_LO_PRI

and

Low Priority/LO_PRI

parameters. Reporting to the field host system only takes place with alarms with a

priority greater than 2.

8. Set the block mode to

Auto

using the

Block Mode/MODE_BLK

parameter,

TARGET

element. For this purpose, the Resource Block and the Setup Transducer Block must

also be set to the

Auto

block mode.

12.2.5 Additional configuration

1. Link the function blocks and output blocks.
2. After specifying the active LAS, download all the data and parameters to the field

device.

12.3 Scaling of the measured value in an AI Block

If the type of linearisation

L_TYPE

indirect

has been selected in an AI block, the

measured value can be scaled within the block. The input range is defined by the

XD_SCALE

parameter through its

EU_0

and

EU_100

elements. This range is mapped

linearly to the output ranged defined by the

OUT_SCALE

parameter through its

EU_0

and

EU_100

elements.

Содержание Micropilot FMR56







































































































































































































Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды

Endress+Hauser Micropilot FMR56, Руководство по эксплуатации

Результаты поиска

Содержание Micropilot FMR56

Отзывы:

Похожие инструкции для Micropilot FMR56

Бренды по названию

Популярные бренды